ODM Non Corrosive Silicone Sealant Window Installation Clear Silicone Adhesive

Quick curingnon corrosive silicone sealant window installation clear silicone adhesive

Art No. A0301

Products details

1. Fast curing
2. Water/rain resistant
3. Anti-fungal/mould
4. both Interior and exterior use

Technical specification

MATERIAL SAFETY DATA SHEET

Section 1: Product & Company Identification

Product Name: SILICONE SEALANT

Product Number: A0301

Section 2: Composition / Information on Ingredients

Component CAS ACGIH OSHA OTHER %

NUMBER TLV PEL LIMITS

Silica 7631-86-9 NE NE NE 12-15

Methyltriacetoxysilane 4253-34-3 NE NE 10ppm 8 -12

Ethyltriacetoxysilane 17689-77-9 NE NE 10ppm 9-13

Nitrogen 7727-37-9 NE NE NE 2-5

Dimethyl siloxane,

Hydroxy-Terminated 70131-67-8 NE NE NE 45-65

Polydimethylsiloxane 63148-62-9 NE NE NE 7-12

Section 3: Hazards Identification

Potential Health Effects:

Inhalation: Dizziness, nose and throat irritation.

Eyes: Irritation, moderate corneal injury.

Skin: NA

Ingestion: NA

Carcinogenicity: OSHA: No IARC: No NTP: No

Chronic Overexposure: None know

Medical Conditions Aggravated by Exposure: None know

-------------------------------------------------------------------------------

Section 4: First Aid Measures

Inhalation: Remove to fresh air. Give artificial respiration if necessary.

Eyes: Flush with large amounts of water for 15 minutes.

Skin: Remove contaminated clothing and wash area with soap and water.

Section 5: Fire-Fighting Measures

Flashpoint: NA Method: NA LEL: ND UEL: ND

Extinguishing Media: Water fog, dry chemical and foam

Hazardous Combustion Products: Acetic acid fumes, CO2, SiO2

Fire-fighting Instructions: Remove containers from fire area if possible. Use

Self-contained breathing apparatus for fire

Fighting. Aerosol cans may explode if heated above

120℉.

NEPA: Health: 1 Flammability: 1 Reactivity: 0

Section 6: Accidental Release Measures

Section 7: Handling and Storage

Handling Procedures: Store in a cool, dry area. Aerosol cans must be maintained below 120℉ to prevent cans from exploding.

Section 8: Exposure Controls / Personal Protection

Engineering Controls: Adequate to prevent accumulation of vapors. Use mechanical means if necessary to maintain levels below the exposure limits. If working in a confined space, follow applicable OSHA regulations.

Respiratory: Use NIOSH/MSHA compliant respirators or self-contained breathing apparatus above exposure limits. Follow OSHA regulations 29 CFR 1910.134.

Section 9: Physical & Chemical Properties

Physical State: Paste Appearance & Odor: clear, white, black, gray

Paste, acetic acid odor

Specific Gravity: 0.97~1.03@25℃ Boiling Point: ND

Freezing Point: ND Vapor Pressure: NA

Evaporation Rate: <1 Vapor Density(air=1) >air

PH: NA Solubility: None in Water

Section 10: Stability and Reactivity

Stability: Stable

Chemical Incompatibilities: Strong oxidizers.

Materials to Avoid: Strong oxidizers. Water causes curing.

Section 11: Toxicological Information

Section 12: Ecological Information

Ecotoxicity: No data available.

Section 13: Transportation Information

Shipping Name: Consumer Commodity

Hazard Class: ORM-D UN Number: NA Packing Group: NA

Section 14: Disposal Considerations

Section 15: Regulatory Information

TSCA: All components are either listed under TSCA or are exempt.

CERCLA/Superfund(RQ): NA

Packing Details

Shelf Life: 12 months

Caution:

1. Silicone Sealant should be applied when room is sufficiently ventilated.
2. Avoid contact with eyes.
3. KEEP IT OUT OF REACH OF CHILDREN;
4. Store it in cool, dry and well-ventilated place below 27 degrees
5. Keep away from fire source;

Detailing Images





Substrates preparation

A. All surface must be clean and dry, degrease and wash off any contaminates that could impair adhesion.

B.Certain plastic may require specific surface treatment to obtain optimum adhesion. Such as the polypropylene, which should need chemical corrosion or plasma treatments?



How to apply

A. Apply a bead of neutral sealant to one of the prepared surface, and then quickly cover with the other substrate to be bonded.

B. On exposure to moisture, the freshly applied material will “skin over” in about 10 to 15 minutes at room temperature and 50% relative humidity. The surface is easily tooled with a spatula.

Why choose us:

1. Over 13 years manufacturing experience;

2. 11 years golden supplier on .com;

3. Exporting experience in over 80 countries;

4. Quality Guarantee: ISO9001,REACH,TUV, Factory Audit, SASO;

5. On time delivery, professional R&D team & satisfied sales service;

6. Customized product available.