Allen Bradley Modules 1785-V40L 1785V40L AB 1785 V40L PLC-5/V40L AB VME rare
Product Description:
For the requested packet interval, enter the number of milliseconds desired between each I/O message
between the ControlLogix processor and the 1203-CN1. The 1203-CN1 can handle a packet interval as
low as 5 milliseconds; therefore, make sure that this value is set to at least Click the "Finish" button to
complete the configuration of the I/O connection in RSLogix 5000. At this point, download your configuration to the ControlLogix processor, then exit RSLogix 5000. To actually schedule the I/O, you will need to start RSNetWorx for ControlNet. Once RSNetWorx starts, go online to the ControlNet network
containing the ControlLogix chassis and 1203-CN1 being configured. Turn on the "Enable Edits" check box, then save the network. This causes the I/O connection created in RSLogix 5000 to be scheduled in the ControlLogix processor. After a few seconds, the I/O LED on the ControlLogix processor and the module LED on the 1203-CN1 should stop blinking and remain green. If they do not, it could indicate a number of I/O-related problems
Related Product Recommendation:
|
Product's Character:
The Remote I/O communications module allows a SCANport product to look and act like a Remote I/O chassis when connected to a programmable controller. Data contained in the input/output image table is transferred between the programmable controller by the Remote I/O scanner, the same as with any Remote I/O chassis. You control the location of data transferred by setting the rack address and
starting group. You control the amount of data by setting the DIP switches on SW3. Important: Thecommunications module does not scale the data that is transferred. Consequently, all scaling of the data must be done in the controller. Refer to the user manual for your SCANport product for details on
device units. Important: The Remote I/O to SCANport conversion is asynchronous. Data sent to the adapter for transfer to the drive must be maintained until the drive has received data.DIP switches on SW3 determine how the data contained in the programmable controller I/O image table is used in the drive. Figure shows an I/O image table.
1785-L40B/C /40 /40 Processor Module - Series C AB
1785-L40B/D /40 /40 Processor Module - Series D AB
1785-L40B/E /40 /40Processor Module - Series E AB
1785-L40C15/E PLC -5/40 PLC -5/40 CONTROLNET Processor - Series E AB
1785-L40C15/F PLC -5/40 PLC -5/40 CONTROLNET Processor - Series F AB
1785-L60B PLC5/60 Processor Module AB
1785-L60B/C PLC -5/60 PLC -5/60 Processor - Series C AB
1785-LT/B Processor Module AB
1785-LT2 /25 /25 Processor Module AB
1785-LT4/A /10, 96077674 /10 Processor AB
1785-ME16 16K EEPROM Memory Cartridge AB
1786-TPYR ControlNet Tap AB
1791-8BC Block I/O Module AB
1792D-16BVT0D 95736401 1792DCBFM INPUT MODULE 16POINT SINK/SOURCE DEVICENET AB
1792D-8BVT0D 95705701 AB Top Input Unit 11-25VDC AB
1792D-CBFM base for: INPUT MODULE 8SINK/SOURCE 4CONNECTORS AB
1793-IB16 Digital Input Module AB
1793-IB16S Digital Input Module AB
1793-IB2XOB2P 24 VDC Combo Module AB
1793-IB2XOB2PS 24 VDC Combo Module AB
1793-IB4 Digital Input Module AB
1793-IB4S Digital Input Module AB
1793-IE2XOE1 Analog Combo Module AB
1793-IE2XOE1S Analog Combo Module AB
1793-IE4 Analog Input Module AB
1793-IE4S Analog Input Module AB
1793-IV16 Digital Input Module AB
A to Z Electronics 50312640000 ASA Board Assy AMAT SemVision cX used working
AMAT RadiSys WHC DR 300 0650-A0750 Computer 2A01640AA4A AMAT SemVision cX workin
HiTek G303/51 High Voltage Power Supply & Cable AMAT 50414710200 used working
AMAT SemVision cX CVC Board 50312570000 working
A to Z Electronics 50312403000 HV Module Assy CDM3-i AMAT SemVision cX working
Parker Veriflow 45700342 Point of Use Regulator SQ140E503PLFSFFM used working
ZTE B9100 ZXMBW BaseBand Unit Type B used working
CMC BMR2005TCD00CEA001 PM Servo Motor w/ RHS-20-50-CC-SP Actuator used working
ASM 2506661-21 Circuit Board Revision B Used Working
ASM 2976285-21 Circuit Board Revision A1 Used Working
ASM 2894203-21 Circuit Board Revision A1 Used Working
ASM 2548860-21 Circuit Board Revision A1 Used Working
ASM 2506556-21 Circuit Board Revision A3 Used Working
ASM 2506416-21 Circuit Board Revision A1 Used Working
AMAT 0021-11486 004 Shutter Pentagon cleaned used working
AMAT 0041-38981 RF Ground Shield Source 300mm RF PVD used working
ASM 2850125-21 Circuit Board Revision B Used Working
The use of the product:
1.electronics manufacturing,
2.oil and gas,
3. petrochemical,
1. Optimize plant operations
2. new and original
3.1 year warranty
Our advantages:
1.We keep more than 10 thousands Transistors in warehouse, it could cut lead time of most items.
2.2000+ suppliers with us, we could help you to get any components which is difficult to get.
3.Risk-free guarantee, 60 days refund. If the item you purchase from our store are not of perfected quality, simply return them to us for replacement or refund.
1.Q: Are the P/N latest?
A: Yes. All P/N are latest and date codes are in 2016 or 2017.
2.Q:Does Moore test the products before shipping ?
A:Yse , we have professional technology staff to test the goods before
3.Q:How about the payment terms ?
A:We frequently use T/T
Send your Inquiry details in the Below, Click "Send" Now!
Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )