ABB Module PM150V08 3BSE003641R1 ABB PM150V08 oil filter housing cooler affordable price

Product Description:

Differential inputs are very useful, if analog sensors are used which are remotely non-isolated (e.g. the minus terminal is remotely earthed). Since the earthing potential is not exactly the same as
AGND1, it has to be measured bipolar in order to compensate measuring errors. Additionally, in case of singlepole configuration, AGND1 would be connected directly to the remote earth potential. This would cause inadmissable (and possibly dangerous) earthing loops. In all configurations using differential inputs two adjacent analog inputs belong together (e.g. EW 6,00 and EW 6,01). For configuration, both inputs must be configured for the desired operating mode, see configuration table Fig. The measured value is calculated by subtraction. The value of the channel with the lower address is subtracted

Related Product Recommendation:

Product's Character:

The trigger of the self-protecting mechanism is displayed by the red LED Ovl as long as the overload is present. In the PLC system an error message is then stored (FK4, error number 4). The open-circuit monitoring begins below ca. 3 mA. The value of the range underflow is stored. If the ope circuit monitoring is configured, the open-circuit event is displayed by the red LED Ovl as long as it is present. In the PLC system an error message is stored (FK4, error number 9). The following figure shows the connection of 2-pole passive- type analog sensors 4...20 mA. If the analog current sensors 4...20 mA are powered from a separate power supply unit, the reference potentials 0V (of the separate power supply unit and the power supply unit for the 07 KT 94) must be interconnected
to each other.In the above example, the AGND terminal remains
unused.

CSC01 Loop Command Sequence Controller ABB
CT 370a GJR2 237500 R1, GJR2237500R0001 CT 370a Module ABB
CT 5536a HEIE420807R1, HEIE420807R0001 CT5536a Module ABB
CTT01 Configuration Tuning Terminal Bailey
CTT02 Handheld Configurator Tuning Terminal ABB
DAC85-10B 57574825BA ULMA D/A Converter Module ABB

DAI 01 P 37131-4-0369628 DAI01 Analog Input Module ABB
DAI 02 0369630M DAI 02 Analog Input Module ABB
DAI 03 P 37141-4-0369631 Analog Input Module ABB
DAI 04 P37131-4-0369632 Analog Input Module ABB
DAI 05 P 37131-4-0336025 DAI 05 Analog Input Module ABB
DAO 01 P 3717-4-0369629 DAO 01 Analog Output Module ABB
DC 371a GJR2 237100 R1, GJR2237100R0001 DC 371a Group Control Module ABB
DC 372a GRJ2 238200R1 , GRJ2238200R0001 Step Control Module ABB
DC 375a GJR2 304400 R1, GJR2304400R0001 DC375a Operating Mode Controller Module ABB
DC 722F A0 3BDH000372R0001 Digital Input/Output Module ABB
DCO 01 0369666 DCO01 Serial Interface Module ABB
DCP 02 P 37211-4-0369654 DCP 02 CPU Module ABB
DCP 10 P37211-4-0338701 DCP10 CPU Module ABB
DCS800-DEMOCASE Field Kit ABB
DCS800-EP1-0020-05 Module Drive ABB
DCS800-EP1-0045-05 Module Drive ABB
DCS800-EP1-0065-05 Module Drive ABB
DCS800-EP1-0090-05 Module Drive ABB
DCS800-EP1-0125-05 Module Drive ABB
DCS800-EP1-0180-05 Module Drive ABB

The use of the product: