ATWINC1510-MR210PB1952 WiFi 802.11b/G/N Transceiver Module 2.4GHz Integrated Trace Surface Mount

Introduction

The ATWINC15x0-MR210xB is a low power consumption 802.11 b/g/n IoT (Internet of Things) module, specifically optimized for low power IoT applications. The module integrates Power Amplifier (PA), Low-Noise Amplifier (LNA), Switch, Power Management and a printed antenna or a micro co-ax (U.FL) connector for an external antenna resulting in a small form factor (21.7 x 14.7 x 2.1 mm) design. It is interoperable with various vendors’ 802.11 b/g/n access points. This module provides Serial Peripheral Interface (SPI) ports to interface with a host controller. The references to the ATWINC15x0-MR210xB module include the module devices listed in the following:

• ATWINC1500-MR210PB

• ATWINC1500-MR210UB

• ATWINC1510-MR210PB

• ATWINC1510-MR210UB

Features

• IEEE® 802.11 b/g/n 20 MHz (1x1) solution

• Single spatial stream in 2.4 GHz ISM band

• Integrated Transmit/Receive switch

• Integrated PCB antenna or U.FL micro co-ax connector for external antenna

• Superior sensitivity and range via advanced PHY signal processing

• Advanced equalization and channel estimation

• Advanced carrier and timing synchronization

• Wi-Fi® Direct (supported till firmware release 19.5.2)

• Soft-AP support

• Supports IEEE 802.11 WEP, WPA, WPA2 security

• Support Enterprise security with WPA/WPA2 (802.1X)(1)

– EAP-TLS

– EAP-PEAPv0/1 with TLS

– EAP-TTLSv0 with MSCHAPv2

– EAP-PEAPv0/1 with MSCHAPv2

• Superior MAC throughput via hardware accelerated two-level A-MSDU/A-MPDU frame aggregation and block acknowledgment

• On-chip memory management engine to reduce host load

• SPI host interface

• Operating temperature range from -40°C to +85°C. RF performance at room temperature of 25oC with a 2-3 dB change at boundary conditions

• Power supply for I/O (VDDIO) rages from 2.7V to 3.6V

• Power supply for DC/DC converter (VBAT) ranges from 3.0V to 4.2V

• Built-in 26 MHz crystal

• Integrated Flash memory for system software

• Power Save modes

– 4 µA Power-Down mode typical at 3.3V I/O

– 380 µA Doze mode with chip settings preserved (used for beacon monitoring) (2)

– On-chip low power sleep oscillator

– Fast host wake-up from Doze mode by a pin or SPI transaction

• Fast Boot options

– On-chip boot ROM (Firmware instant boot)

– SPI flash boot

– Low-leakage on-chip memory for state variables

– Fast AP re-association (150 ms)

• On-chip Network stack to offload MCU

– Network features TCP, UDP, DHCP, ARP, HTTP, TLS and DNS

– Hardware accelerators for Wi-Fi and TLS security to improve connection time

• Hardware accelerator for IP checksum

• Hardware accelerators for OTA security

• Small footprint host driver

• Wi-Fi Alliance® certifications for Connectivity and Optimizations

Block Diagram

specification of ATWINC1510-MR210PB1952

ORIGINAL

Our company ensures that each batch of products comes from the original factory, and can provide original labels and professional testing agency reports.

PRICE

We provide a variety of quotation channels, and sign the order contract after negotiation.

TRANSACTION

After communication and agreement, we will guide you to arrange payment.

DELIVERY CYCLE

Delivery on the same day, generally 5-12 working days, may be slightly delayed during the epidemic, we will follow up the whole process.

TRANSPORT

We will choose the appropriate transportation mode according to your country.

PACKAGING

After communication with you, we will choose the appropriate packaging method according to the weight of the goods to ensure the safe delivery of the goods.