1, Detailed datasheet of this parts
Basic size information | |||
Suitable housing | A1250H series | ||
Category | wafer | ||
Material of wafer's pin | phosphor bronze or tin-plated | ||
Lock to mating part | None | ||
Stackable | No | ||
Circuits | 2 to 16pins | ||
Wire insulation diameter | 0.90mm Max. | ||
Electrical properties | |||
Current Rating | 1A AC, DC | ||
Voltage Rating | 125V AC, DC | ||
Contact Resistance | 20mΩ Max | ||
Insulation Resistance | 100mΩ min | ||
Withstanding Voltage | 500V AC/minute | ||
Mechanical properties | |||
Temperature range | -25℃ to 85 ℃ | ||
Other information please kindly check the following picture. |
2, Relevant drawing and report
Folllowing pictures are out testing report and exact engineering drawing for your information, please kindly check it, wish it can help you to get what you really need.
Mechanical Performance
Test Description | Procedure | Requirement | ||
5-1 | Actuator Insertion & Withdrawal Force | Insert and withdraw connectors at the speed rate of 25±3mm / minute. | Refer to paragraph 7 | |
5-2 | Crimping Pull Out Force | Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) | AWG#28 | 1.0kgf (Min) |
AWG#30 | 0.8kgf (Min) | |||
AWG#32 | 0.5kgf (Min) | |||
5-3 | Terminal Insertion Force. | Insert the crimped terminal into the housing. | 0.50kgf (Max.) | |
5-4 | Terminal/Housing Retention Force. | Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. | 0.50kgf (Min.) | |
5-5 | Pin Retention Force | Apply axial push force at the speed rate of 25±3mm / minute | 0.50kgf (Min.) | |
5-6 | Durability | When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. | Contact Resistance 40mΩ (Max.) | |
5-7 | Vibration | Amplitude: 1.5mm P-P Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes. (Based upon MIL-STD-202 Method 201A) | Appearance No Damage. Contact Resistance 40mΩ (Max.) Discontinuity 1 μsec.(Max.) | |
5-8 | Physical Shock | 490m/s²{50G},3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) |
Environmental Performance And Others
Test Description | Procedure | Requirement | |
6-1 | Temperature Rise | Carrying rated current load.(Based upon UL 498) | 30℃(Max.) |
6-2 | Heat Resistance | 85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) | Appearance No Damage. Contact Resistance 40mΩ (Max.) |
6-3 | Cold Resistance | -25±3℃,96 hours (Based upon JIS C0020) | |
6-4 | Humidity | Temperature: 40±2℃ Relative Humidity : 90~95% Duration: 96 hours (Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B) | Appearance No Damage. Contact Resistance 40mΩ (Max.) Insulation Resistance 10MΩ (Min.) Dielectric Withstanding Voltage Must meet 4-3 |
6-5 | Temperature Cycling | 5 cycles of: a) -55℃ 30 minutes b) +85℃ 30 minutes (Based upon JIS C0025) | Appearance No Damage. Contact Resistance 40mΩ (Max.) |
6-6 | Salt Spray | Tin-plated 16 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101C Cond. B) | |
6-7 | SO2 Gas | 24 hours exposure to 50±5ppm. SO2 gas at 40±2℃. | |
6-8 | NH3 Gas | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
3, Our advantage
You can know our advantages from the below description,
1. R & D personnel with over 12 year's experience
2. Automated facilities for cost-efficient production
3. Conforming to ISO9001/ ISO14001/RoHS/REACH standards
4.Short lead times:5~8 working days
5.OEM/ODM orders welcome
6.One-stop service from R&D and mold design to mass production
7.All components and accessories made in-house
8.Own lab with 2.5 Dimensional imager, Automatic force tester, Environment tester, Stiffness tester, Insulation tester, Micro-resistor tester, Salt spray tester