A.1 Input Characteristics: | |||
ITEM | CONDITION | SPECIFICATION | |
A.1.1 Rated Input Voltage: | 100Vac ~ 240Vac | ||
A.1.2 Input Voltage Range: | Continuously | 90Vac ~ 264Vac | |
A.1.3 Input Frequency Range: | Continuously | 50Hz ~ 60Hz (+/-5%) | |
A.1.4 Input Current: | 115Vac-230Vac | £ 2.5A for 115 Vac/ Iout:6.25A | |
£ 1.2A for 230 Vac/ Iout:6.25A | |||
A.1.5 Efficiency: | 115Vac / Iout:6.25A | Average ³90% Average ³91% | Meet: |
( Warm up 30 minutes later ) | 230Vac / Iout:6.25A | -1 | |
US DOE Level VI | |||
-2 | |||
CoC V.5 Tier 2 | |||
A.1.6 No Load Power Consumption | 115Vac / Iout:0A 230Vac / Iout:0A | £ 0.15W | |
£ 0.15W | |||
A.1.7 Inrush current | 115Vac,230Vac / Iout:6.25A | <40A@115Vac | |
,At Cold start (Ta=25°C) | <80A@230Vac | ||
A.1.8 Power Factor | ³0.98@115Vac/ Iout:6.25A | ||
³0.93@230Vac/ Iout:6.25A | |||
A.2. Output Characteristics: | |||
✽Measured at the end of CN200. | |||
ITEM | CONDITION | SPECIFICATION | |
A.2.1 Output Rated Voltage: | 24V | ||
A.2.2 Output Current: | At constant voltage mode | 0A to 6.25A | |
(Please Refer to "Derating Curve") | (@Ta50, Convection cooling) 6.25A To 8.33A | ||
(@with 7 CFM forced air | |||
provided by user) | |||
A.2.3 Output Voltage Setting: | At the output end of CN200 | 24V (± 3 %) | |
A.2.4 Output Voltage Ripple and Noise: | 115Vac, 47Hz to 63Hz 230Vac, 47Hz to 63Hz | £ 240 mVp-p. | |
(0.1uF Ceramic Cap. and 47uF Tantalum Cap. Paralleled between the output connector, BW=20M Hz, Ta=0~50°C) | |||
A.2.5 Turn-On Delay Time: | At nominal AC input voltage and output load is 6.25A, output voltage shall remain regulation . | £ 1500 ms. | |
A.2.6 Rise Time: | DC output rise time from 10% to 90% of Output Voltage | £ 50 ms. | |
A.2.7 Hold Up Time: | At 115Vac | ³ 20 ms@ Load 6.25A | |
³ 8 ms@ Load 8.33A | |||
A.2.8 Over-shoot: | 100Vac / load 6.25A 240Vac / load 6.25A | £ 5%. | |
A.2.9 Fan Driver: | 12V/0.5A(Max)@CN201 | ||
A.2.10 Dynamic Load Change: | (1) Output load step is: 1) 0% ~ 50% 2)50% ~ 100% | 24V ±10% | |
(2) S/R = 0.5A/us | |||
(3) Frequency is 100Hz and 1KHz, 50%duty | |||
.A.2.11 Output Derating Versus Operating Ambient Temperature | |||
A.3. Protection Characteristics: | |||
ITEM | CONDITION | SPECIFICATION | |
A.3.1 Short Circuit Protection: | When an internal fault occurs, or an external fault is applied to the power supply, such that an overload or short circuit is applied to the output, the power supply shall shut down and enter auto-recovery mode. | Auto-recovery and no damage. | |
A.3.2 Over Voltage Protection: | The output voltage will limit under 35V that means to protect while over voltage happened at output terminal that caused by internal fault. | Shut down and no damage | |
A.3.3 Over Power Protection: | The Power Supply Unit will enter into shut down while the abnormal thermal rise occurs. | Auto-recovery and no damage | |
A.3.4 Over Temperature Protection: | The power supply will enter into shut down while the abnormal thermal rise occurs, It will enter into normal condition if the fault condition is removed. | No fire, no smoke | |
Shut down and no damage | |||
A.3. Protection Characteristics: | |||
ITEM | CONDITION | SPECIFICATION | |
A.3.1 Short Circuit Protection: | When an internal fault occurs, or an external fault is applied to the power supply, such that an overload or short circuit is applied to the output, the power supply shall shut down and enter auto-recovery mode. | Auto-recovery and no damage. | |
A.3.2 Over Voltage Protection: | The output voltage will limit under 35V that means to protect while over voltage happened at output terminal that caused by internal fault. | Shut down and no damage | |
A.3.3 Over Power Protection: | The Power Supply Unit will enter into shut down while the abnormal thermal rise occurs. | Auto-recovery and no damage | |
A.3.4 Over Temperature Protection: | The power supply will enter into shut down while the abnormal thermal rise occurs, It will enter into normal condition if the fault condition is removed. | No fire, no smoke | |
Shut down and no damage | |||
B.13 Conducted Emission | 1. Full Load | Designed to meet EN55032 ClassB, | |
2. The power supply with internal filter can meet. | FCC Class B | ||
VCCI Class B | |||
B.14 Radiated Emission | 1. Full Load | Designed to meet EN55032 Class B FCC Class B | |
2. The power supply with internal filter can meet. | VCCI Class B | ||
B.15 MTBF | Measured at 230Vac input, Full Load and 25°C ambient temperature (BELL CORE SR-332) | ≧200000 Hours | |
B.16 Dielectric Strength (Hi-Pot) | Input to Output | 3000Vac | |
Input to Ground Output to Ground | 1500Vac | ||
1500Vac | |||
B.17 Leakage Current: | 240Vac / 50Hz | £ 1mA | |
B.18 Isolation Resistance: | Primary to Secondary: 500Vdc | ≧100 M ohms | |
B.19 Temperature: | Operating | -20°C to +70°C | |
Storage | -40°C to +85°C | ||
B.20 Humidity: | Operating | 10% ~ 90% | |
Storage | 5% ~ 95% | ||
B.21 Vibration | Storage: | Normal operation shall be continued | |
a. Frequency : 10 to 55Hz | |||
b. Test Mode : Sweep Sine | |||
c. Sweep Mode : Linear Time | |||
d. Sweep Time : 30min | |||
e. Displacement : 0.75mm | |||
f. Scan Speed : 1.5Hz/sec | |||
Operation, 0.01g²/Hz at 5 Hz sfffloping to 0.02g²/Hz at 20 Hz, and maintaining 0.02g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13gRMS. | |||
The duration shall be 20 minutes per axis for all three axes on all samples. | |||
B.22 Product Ecology Requirement | All materials, parts and subassemblies must not contain restricted materials as defined in directive | FSP will always follow latest worldwide RoHS / REACH | |
regulations | |||
B.23 Acoustic Noise: | 115Vac / 230Vac | The EUT <25dB | |
C. Mechanical Characteristics: | |||
ITEM | CONDITION | SPECIFICATION | |
C.1 Dimension (Length x Width x Height): | 127x76.2x32.6mm | ||
(5 inch* 3 inch*1.28 inch) | |||
C.2 Weight | 400 grams (0.485 lbs.) approx (typical) | ||
C.3 Input Connector (IN1) | Input Connector (IN1) | JWT A3963WV2-3P-D or | |
equivalent. | |||
C.4 Output Connector | Output Connector (CN200) | JWT A3963WV2-6P or | |
equivalent. | |||
C.5 Output Fan Connector | Fan driver (CN201) | JWT A2543WV2-2P or | |
equivalent. | |||
C.6 Ground pad | FG | 8 x 6.35 x 0.8 mm |
The FSP200-P35-A24 Features
Product Display