Quick details

– Rapid response protection for electrical machines
– Compact size for easy assembly into windings
– Silvered copper leads

Description

PTC thermistors act as thermal protectors for electrical motors. They are available with or without an insulated sleeve and have flexible connecting leads. PTC thermistors have a non-linear resistance/temperature response. At a specified temperature the resistance changes rapidly to a very high value.

Application

Motor Protection and Electronics.

Specification

Dimensions (mm)
CYGM1 Single Thermistor with shrunk-sleeve & epoxy seal Type Response Temp. ϑNAT Color Code CYGM1 C508 80±5 white-white CYGM1 C509 90±5 green-green CYGM1 C510 100±5 red-red CYGM1 C511 110±5 brown-brown CYGM1 C512 120±5 grey-grey CYGM1 C513 130±5 blue-blue CYGM1 C514 140±5 white-blue CYGM1 C545 145±5 white-black CYGM1 C515 150±5 black-black CYGM1 C655 155±5 blue-black CYGM1 C516 160±5 blue-red CYGM1 C517 170±5 white-green CYGM1 C518 180±5 red-white
CEF1 Mount-on Sensor in isolated brass/aluminium housing Type Response Temp. ϑNAT Color Code CEF1 C508 80±5 white-white CEF1 C509 90±5 green-green CEF1 C510 100±5 red-red CEF1 C511 110±5 brown-brown CEF1 C512 120±5 grey-grey CEF1 C513 130±5 blue-blue CEF1 C514 140±5 white-blue CEF1 C545 145±5 white-black CEF1 C515 150±5 black-black CEF1 C655 155±5 blue-black CEF1 C516 160±5 blue-red CEF1 C517 170±5 white-green CEF1 C518 180±5 red-white When ordering please specify thread size, otherwise the stock M4 size will be supplied.
CYGM3 Triple Thermistor with shrunk-sleeve & epoxy seal Type Response Temp. ϑNAT Color Code CYGM3 C508 80±5 white-yellow-yellow-white CYGM3 C509 90±5 green-yellow-yellow-green CYGM3 C510 100±5 red-yellow-yellow-red CYGM3 C511 110±5 brown-yellow-yellow-brown CYGM3 C512 120±5 grey-yellow-yellow-grey CYGM3 C513 130±5 blue-yellow-yellow-blue CYGM3 C514 140±5 white-yellow-yellow-blue CYGM3 C545 145±5 white-yellow-yellow-black CYGM3 C515 150±5 black-yellow-yellow-black CYGM3 C655 155±5 blue-yellow-yellow-black CYGM3 C516 160±5 blue-yellow-yellow-red CYGM3 C517 170±5 white-yellow-yellow-green CYGM3 C518 180±5 red-yellow-yellow-white

OPERATION
PTC thermistors exhibit very high sensitivity over a narrow temperature band. For temperature measuremen
in this range, NTC thermistors are easier to measure and more accurate.

PTC thermistors are especially suited as temperature sensors for monitoring the windings of electric machines, and also for use in simple fail-safe circuitry. When a given temperature (nominal response temperature qNAT) is exceeded, the circuit can be switched off through a relay or amplifier, since the PTC-sensor will have an extremely high ohmic value in the region of its response temperature. This will have the same effect as a break in the circuit or a failure of the thermistor.

TECHNICAL DATA
Nominal response temperature:	80° C to 180° C in steps of 10°, plus 145° and 155°
Max. allowable operating temp.	T max. 200° C
Max. allowable operating voltage at +25° C	Umax 25V (per bead)
Max. allowable power dissipation at +25° C	690 mW
Insulation strength (between leads and outer insulation) also for threaded sensor	2.5 kV
Conductors - silvered copper wire with teflon insulation	PTFE
Insulation stripping	approx 10 mm
Conductor cross-section	0.25 mm 2 for single, double and triple PTC’s

CONDUCTOR LENGTHS
Single PTC 500 mm 6 10 mm
Triple PTC 500 - 180 - 180 - 500 mm 6 10 mm

SPECIAL VERSIONS
PTC’s are also available in many special housings (can be manufactured to customers specifications)

INSTALLATION TIPS
For PTC temperature sensors in electrical windings:
- the thermistors can only be inserted in the windings before impregnation
- it is advisable to embed one in each phase, if possible in the centre of the coil generating most heat, and generally on the outflow side of any air movement
- air inflow onto the temperature sensor will interfere with heat transfer
- if using varnish/lacquer which is not chemically neutral, suitability tests must be undertaken by the customer
- WARNING! It is very important that the sensor must be installed parallel with the copper of the winding, so that the teflon leads can assume the form of the rest of the winding and thereby retain the highvoltage resistance rating.

- PTC’s are classified according to their nominal response temperature ϑNAT but all have similar resistance characteristics to simplify the choice of switching device; the relationship of resistance to temperature of all these PTC’s is as follows:

STANDARD RESISTANCE VALUES

Single PTC
Temp. ° C	Resistance Ω	Measuring Voltage V
-20 to ϑNAT -20	250 max./100max.	2.5
ϑNAT -5	550 max.	2.5
ϑNAT	1.000	2.5
ϑNAT +5	1.330 min.	2.5
ϑNAT +15	4.000 min.	7.5

Triple PTC
Temp. ° C	Resistance Ω	Measuring Voltage V
-20 to ϑNAT -20	750 max./300max.	7.5
ϑNAT – 5	1.650 max.	7.5
ϑNAT+5	4.000 max.	7.5
ϑNAT +15	4.000 min. *	7.5

* One PTC might reach ϑNAT + 15 °C, while the second or even both of the others could still remain at room temperature.

The PTC’s resistance values for motor protection are specified in DIN 44081/44082. Resistance values below ϑNAT –20 are not specified, and resistance when cold is no indication of the PTC’s condition. It is ideally between 40 - 200 ohms but can be anywhere between 35 - 250 ohms.

The greatest resistance change occurs between +/-5 °C either side of ϑNAT, being at least 15%/K.


QUALITY STANDARD
Random testing is carried out according to DGQ P90/P10 (DIN 40080). AQL values can be fixed by arrangement.

ORDERING INFORMATION

Quantity	Type	Temp. Code No.	Resistance max.
1.000	CYGM1	C 510	250 ohms

TEMPERATURE-RESISTANCE CURVE