J1772 EVSE Type1 Level 2 Station EV Wall Box Charger For Leaf Charging
✔ Press the E-stop button to stop operation at any moment, especially in the event of a malfunction.
Power Specification
|
||||
AC Power Input Rating
|
SAE Standard
|
IEC Standard
|
||
AC Level 2
|
1-Phase
|
3-Phase
|
||
240V
|
220V ± 15%
|
380V ± 15%
|
||
AC Power Output Rating
|
3.5kW/16A
|
3.5kW/16A
|
11kW/16A
|
|
7kW/32A
|
7kW/32A
|
22kW/32A
|
||
10kW/40A
|
N/A
|
43kW/63A
|
||
Rated Frequency
|
50/60Hz
|
50/60Hz
|
50/60Hz
|
|
Connector Type
|
SAE J1772 (Type 1)
|
IEC 62196-2 (Type 2)
|
||
User Interface & Control
|
||||
Charging Control
|
Plug and Play, RFID Card or App
|
|||
Display Screen
|
4.3-inch LCD Screen
|
|||
Voice Prompt (Optional)
|
Voice guide of the charging process in English
|
|||
Indicators
|
4 LED indicators-Power/Connect/Charging/Fault
|
|||
External Communication
|
LAN (RJ-45) and Wi-Fi
|
|||
OCPP Protocol (Optional)
|
1.6 or 2.0.1
|
|||
Environmental
|
||||
Storage Temperature
|
-40 to 75℃ (-40 to 167℉) ambient
|
|||
Operating Temperature
|
-30 to 55℃ (-22 to 131℉) ambient
|
|||
Operating Humidity
|
Up to 95% non-condensing
|
|||
Altitude
|
≤2000m
|
|||
Protection
|
||||
Protection Ratings
|
IP 65
|
RCD
|
Type A / Type B
|
|
Over Voltage Protection
|
Yes
|
Under Voltage Protection
|
Yes
|
|
Over Load Protection
|
Yes
|
Short Circuit Protection
|
Yes
|
|
Earth Leakage Protection
|
Yes
|
Ground Protection
|
Yes
|
|
Over-temp Protection
|
Yes
|
Surge Protection
|
Yes
|
|
Wallbox Mechanical
|
||||
Dimension (H x W x D, mm)
|
410 x 260 x 164
|
|||
Weight
|
1-phase<10kg; 3-phase<12kg
|
|||
Charging Cable Length
|
5m or Customize Length
|
|||
Enclosure Material
|
Front-Panel: Tempered Glass; Back-cover: Metal Plate
|
|||
Mounting Pole Mechanical (Optional)
|
||||
Dimension (H x W x D, mm)
|
1400 x 200 x 100
|
|||
Weight
|
<8kg
|
|||
Enclosure Material
|
Metal
|
Attention to know
EV chargers are splash, water and dust resistant and have been tested under strictly controlled laboratory
conditions to achieve an IP65 rating in accordance with IEC standard 62196. However, the resistance to splashes, water and dust is not permanent and may weaken over time under normal use. Damage caused by liquids is not covered by the warranty.
To prevent damage to your charger from liquids, please avoid the following situations :
1. Exposing the charger to pressurised water or high velocity water flow.
2. Intentionally submerging the charger in water.
3.Operating the charger beyond the recommended temperature range or in extremely humid environments
4. Dropping the charger or subjecting it to other shocks.
5. Disassemble the charger, including removing the screws.
If the charger comes into contact with liquid, turn off all power until it is completely dry.
Placing the unit in front of a fan so that cold air is blowing directly on the charging connector may help to speed up the drying process.
Do not use an external heat source to dry the charger, or insert foreign objects such as cotton swabs or paper towels into the charging port.