Threaded In Line Load Cell 30kN 50kN Rod End Force Sensor 100kN 200kN 300kN 500kN

Threaded Inline Load Cell FLH is made of 17-4 stainless steel based on strain gauge technology intended for both traction and compression force measurement. Inline type pull push load cells are designed to be mounted inline to the load axis with rugged structure for industrial applications.The Rod End Load Cell FLH can be easily mounted to existing system through the threaded rods located on both sides of the transducer, these metric threads can also be used to mount attachments, such as female eye bolt,bolt adapter,etc.,to fit different usage requirements. Tension Compression Sensor FLH offers 0-10kN / 0-20kN / 0-30kN / 0-50kN / 0-100kN / 0-200kN / 0-300kN / 0-500kN / 0-1000kN nine rated measuring ranges, each sensor is integrated with a 3-meter-long 4-core shielded cable,the cable comes with a free end which makes it easy to assemble any types of connectors for electrical connection. Force Transducer FLH is normally used for press-in force measurement, cylinder thrust force measurement, auto equipment, production line, hand press machines,etc.

A load cell is a transducer that converts load or force acting on it into electronic signal which is proportional to the applied force.The acting force causes deformation of the measuring element,the bonded strain gage deforms accordingly which will cause the resistance change of the wheatstone bridge,under constant power supply,the output signal between Sig+ and Sig- will change proportionally,thus the load/force can be measured by measuring the output signal from the load cell.Threaded Inline Load Cell FLH is designed to measure both tension and compression force,outputs millivolt signal ranging -22.5mV...+22.5mV, and signal amplification may be required for most applications, a load cell signal conditioner can be used to get -5~5V, 0-10V or 4-20mA signal which is proportional to applied force.The amplified output is can be easily processed by PLCs and data acquisition software.The applied force can be displayed through a force indicator,force indicator FPT is integrated with high accuracy/low noise 24 bit Sigma-Delta ADC,sampling speed up to 960Hz makes it suitable for both static and dynamic measurement;FPT also supports Modbus RTU protocol with RS485 or RS232 communication port,amplified signal 0-5V,0-10V,0-20mV or 4-20mA is also achievable from FPT.

Specifications

Output signal of load cell and amplifier:
Load cell output: = (Power supply * Rated output) * Load / Capacity
Rated output of M12 Threaded Inline Load Cell FLH is normally around 1.5mV/V.
Power supply of Rod End Tension Compression Load Cell FLH is normally within 3-15V.
Load / Capacity is within 0-1.
So the output range of In Line Load Cell FLH is normally within -22.5mV…+22.5mV for tensile and compressive force measurement.
Example one: Threaded In-line Load Cell FLH-20kN with 1.5mV/V sensitivity powered by 5V DC, the output range is -7.5mV...+7.5mV.
Example two: M12 Threaded Rod End Force Sensor FLH-10kN with 1.4mV/V rated output powered by 10V DC, the output range is -14mV...+14mV.

The mV/V output from the wheatstone bridge sometimes can hardly be processed directly, a signal conditioner can be used with the load cell to deliver -5~5V, 0-10V or 4-20mA output.
Example one: Inline Type Tension Compression Force Sensor FLH-10kN working with amplifier FSC(-10-10V)-24V, the Load-Voltage relationship will be 0-10kN compression force VS 0-10V output, 0-10kN traction force VS 0-(-10V), which is linear regardless of the measurement error, 1V output corresponds to 1kN compressive load, (-2V) output corresponds to 2kN tensile load, and so on.
Example two: Rod End Tensile Compressive Force Transducer FLH-20kN working with amplifier FSC(4-12-20mA)-24V, the Force-Current relationship will be 0-20kN compressive force VS 12-20mA output, 0-20kN tensile force VS 12-4Ma, which is linear regardless of the measurement error, 12mA output corresponds to “0” load, 12.8mA output corresponds to 2kN compression load, 8mA output corresponds to 10kN tension load, and so on.

Threaded In Line Load Cell 200kN 300kN 500kN Rod End Force Sensor 100kN 50kN 30kN 20kN

Click here to download datasheet