10.1 Inch 1024x600 High Brightness LVDS IPS TFT Display/EK79001+EK73215/H101A9WSIFTKN40
Product parameters
Dimensions (mm) - 235.00x143.00x 6.95
Display size (mm) - 10.1 inch
Effective size mm - 222.72x125.28
Perspective - Full Perspective
Connection method PIN number - 40PIN
Interface method - LVDS
Working temperature - -20~70℃
Supply Voltage - 3.3V
General Feature
Item | Standard Value | Unit |
Display Size | 10.1 | Inch |
Number of Pixels | 1024(H)*3(RGB)* 600(V) | dots |
Active Area | 222.72(H)* 125.28(V) | mm |
Outline Dimension | 235.00(H) * 143.00(V) * 5.30(D) <TFT> | mm |
Viewing Direction | FULL O'clock | - |
TFT Interface | LVDS | - |
TFT Driver IC | EK79001+EK73215 | - |
TFT Driver Condition | VCI=3.3V(Typ) | V |
Backlight | White LED/42 PCS/6 LEDs serial 7 ways parallel | - |
Touch Panel | Without TP | - |
CTP Driver IC | - | |
CTP Driver Condition | VDD=3.3V(Typ) | 伏 V |
Operation Temperature | -20 ~ 70 | 摄氏度 |
Storage Temperature | -30 ~ 80 | 摄氏度 |
TFT Pin Description
Pin NO. | Symbol | Description |
1 | VCOM | TFT Common Electrode Voltage |
2~3 | VCI | Digital Power |
4 | NC | No Connect |
5 | RESX | Global reset pin. Active low to enter reset state. Usually pulled high. For stability, an RC delay circuit needs to be connected externally. (RESX delay VCI greater than 1ms) |
|
STBYB | Standby mode, normally pull high. STBYB = "VCI", normal operation STBYB = “GND”, Standby mode |
7 | GND | Ground |
8 | D0N | LVDS negative differential data |
9 | D0P | LVDS positive differential data |
10 | GND | Ground |
11 | D1N | LVDS negative differential data |
12 | D1P | LVDS positive differential data |
13 | GND | Ground |
14 | D2N | LVDS negative differential data |
15 | D2P | LVDS positive differential data |
16 | GND | Ground |
17 | DCKN | LVDS negative differential clock |
18 | DCKP | LVDS positive differential clock |
19 | GND | Ground |
20 | D3N | LVDS negative differential data |
21 | D3P | LVDS positive differential data |
22 | GND | Ground |
23~24 | NC | No Connect |
25 | GND | Ground |
26~27 | NC | No Connect |
28 | HSD | Data channel selection STBYB = "VCI", 6 bit STBYB = “GND”, 8 bit |
29 | AVDD | Analog Power |
30 | GND | Ground |
31~32 | LEDK | LED Cathode,Not connected here |
33 |
L/R | Horizontal scan direction control pin L/R= "VCI", From left to right(Default) L/R= “GND”, From right to left |
34 |
U/D | Vertical scan direction control pin U/D= "VCI", From down to up. U/D= “GND”, From up to down.(Default) |
35 | VGL | TFT Gate OFF Voltage |
36~37 | NC | No Connect |
38 | VGH | TFT Gate ON Voltage |
39~40 | LEDA | LED Anode,Not connected here |