4.3 Inch 480x800 Sunlight Readable TFT Display Module NT35510/TFT_H043A4WVIST5N60
Product parameters
Dimensions (mm) - 60.86x104.50x 2.50
Effective size mm - 56.16x93.60
Product Application - Handheld Instruments
Angle - Full Angle
Backlight type or brightness - 500cd/m2
Connection method PIN number - FPC-60PIN
Supply voltage - 3.3v
General Feature
Item | Standard Value | Unit |
Display Size | 4.3” | -- |
Number of Pixels | 480(H)x3(RGB)*800(V) | -- |
Active Area | 56.16(H) *93.60(V) | mm |
LCM Outline Dimension | 60.86(H) ×102.57× 2.70(V) | mm |
Viewing Direction | Full O’Clock | - |
LCM Interface | With CPU / RGB / MIPI / MDDI Interface | - |
LCM Driver IC | NT35510 | - |
LCM Driver Voltage | IOVCC=1.8V,VCI=3.3V (Typ) | V |
Backlight | White LED | - |
Touch Panel | Without Touch Panel | - |
CTP Driver IC | - - - | - |
CTP Driver Voltage | - - - | V |
CTP I/O Digital Voltage | - - - | V |
Operation Temperature | -20~70 | ℃ |
Storage Temperature | -30~80 | ℃ |
Pin Description
Pin NO. | Symbol | Description |
1,2 | GND | Ground |
3 |
D0N | ♦These pins are DSI-D0+/- differential data signals if MIPI interface is used. ♦These pins are MDDI_DATA0_P/M differential strobe signals if MDDI interface is used. ♦If not used, please fix this pin at GND. |
5 |
D0P | |
5,6 | GND | Ground |
7 |
DCLKN | ♦These pins are DSI-CLK+/- differential clock signals if MIPI interface is used. ♦These pins are MDDI_STB_P/M differential strobe signals if MDDI interface is used. ♦If not used, please fix this pin at GND. |
8 |
DCLKP | |
9 | GND | Ground |
10 |
D1N | ♦These pins are DSI-D1+/- differential data signals if MIPI interface is used. ♦These pins are MDDI_DATA1_P/M differential strobe signals if MDDI interface is used. ♦If not used, please fix this pin at GND. |
11 |
D1P | |
12 | GND | Ground |
13 | VCI | Analog Power |
14 | IOVCC | Power supply for interface system |
15 | VSD | ♦ Vertical synchronizing input signal for RGB interface. ♦ If not used, please fix this pin at GND. |
16 | HSD | ♦ Horizontal synchronizing input signal for RGB interface. ♦ If not used, please fix this pin at GND. |
17 | PCLK | ♦ Pixel clock signal for RGB interface. ♦ If not used, please fix this pin at GND. |
18 | DEN | ♦ Data enable signal for RGB interface. ♦ If not used, please fix this pin at GND. |
19-42 |
DB0-DB23 | ♦ Data Bus. ♦ If not used, please fix this pin at GND. |
43 | RESET | LCM Reset Pin. |
44 |
CSX | ♦ Chip select input pin (“Low” enable) in 80-series MPU I/F and SPI I/F. ♦ This pin is not used for MIPI or MDDI I/F, please fix this pin at GND. |
45 | RDX | ♦ Read enable in 8080 MCU parallel IF. Low-active. ♦If not used, please fix this pin at GND. |
46 |
WRX | ♦ Write enable in MCU parallel interface ♦ In SPI mode, this pin is used as SCL. ♦ In I2C mode, Serial input clock in I2C I/F ♦ If not used, please fix this pin at GND. |
47 | DCX | ♦ Display data/command selection pin in parallel IF. ♦ If not used, please fix this pin at GND. |
48 |
SPI_SDI | ♦ In SPI mode,SPI interface input/output pin. ♦ In I2C mode, Serial input/output signal in I2C I/F. ♦ If not used, please fix this pin at GND. |
49 | SPI_SDO | ♦ In SPI mode,SPI interface output pin. ♦ If not used, please let this pin open. |
50 |
TE | ♦ Tearing effect signal is used to synchronize MCU to frame memory writing. ♦ If not used, please let this pin open. |
51-54 | IM0-IM3 | The MCU interface mode select |
55 |
PSWAP | ♦ Input pin to select HSSI_D0/D1 data lane sequence and polarity in high speed interface only. ♦ For MIPI interface, both DSWAP and PSWAP function are available. ♦ For MDDI interface, only PSWAP function is available. i.e. DSWAP=1 in below table is invalid. ♦ If not used, please fix this pin at GND. |
56 |
DSWAP | |
57 |
LANSEL | ♦ Input pin to select 1 data lane or 2 data lanes in MIPI/MDDI interface. ♦ If not used, please fix this pin at GND. |
58 | MTP | No Conect |
59 | LED_A | LED Anode |
60 | LED_K | LED Cathode |