Industrial Servo Motor Yaskawa SGMGH-55ACA61 5500W 42.1A AC Servo Motor
Function:Control
High Speed
Rated Torque:35 Nm
Yaskawa Sigma 2 (?-II Series) Three-phase - 42.1A, 5500W, 200V, 5.5kW Servo Motor
Yaskawa | Sigma 2 (?-II Series) | Servo Motor
Repair for Yaskawa Sigma 2 (?-II Series) is available. MRO is committed to customer satisfaction!!
SGDP-02APAY108+SGMPH-02ACA-SW11 |
SGDP-02BP |
SGDP-02BP+SGMAH-02BBAB1 |
SGDP-02BPA |
SGDP-04APA |
SGDP-04APAY108 |
SGDP-04APAY108+SGMPH-04ACA-SW11 |
SGDP-04BP |
SGDP-08APA |
SGDP-A3APAY108 |
SGDP-A3BP |
SGDP-A5BP |
SGDP-O1AP |
SGDP-O2AP |
SGDP-O4AP |
SGDP-O8AP |
SGDS-01A01A |
SGDS-01A01A+SGMAS-01ACA21 |
SGDS-01A02AY524 |
SGDS-01A05A |
SGDS-01A12A |
SGDS-01A15A |
SGDS-01F01A |
SGDS-01F12A |
SGDS-02A01A |
SGDS-02A01A SGMAS-02ACA21 |
SGDS-02A01A+SGMAS-02ACA21 |
SGDS-02A01A+SGMAS-02ACA2C |
SGDS-02A01A+SGMAS-C2ACA21 |
SGDS-02A01AR501 |
SGDS-02A01ARY501 |
SGDS-02A05A |
SGDS-02A12A |
SGDS-02A12AY506-E |
SGDS-02A15A |
SGDS-02A72A |
Installation Site
Protective covers are attached to the top and bottom of the Drive. It is recommended to remove the protective covers before
operating a CIMR-E7U2030/4055 Drive and smaller in a panel to obtain the 113°F (45°C) ambient operating temperature.
Observe the following precautions when installing the Drive:
• in a clean location which is free from oil mist and dust.
• in an environment where metal shavings, oil, water, or other foreign materials will not get into the Drive enclosure.
• in a location free from radioactive materials.
• in a location free from harmful gasses and liquids.
• in a location free from excessive vibration.
• in a location free from chlorides.
• in a location away from direct sunlight.
• on a non-combustible surface.
Controlling the Ambient Temperature
To enhance the reliability of operation, the Drive should be installed in an environment free from extreme temperature variations. If the Drive is installed in an enclosure, use a cooling fan or air conditioner to maintain the internal air temperature below 113°F (45°C).
Protecting the Drive from Foreign Matter
During Drive installation and project construction it is possible to have foreign matter, such as metal shavings or wire clippings, fall inside the Drive. To prevent foreign matter from falling into the Drive, place a temporary cover over the Drive. Always remove the temporary cover from the Drive before Start-Up. Otherwise, ventilation will be reduced, causing the Drive to overheat.
OTHER SUPERIOR PRODUCTS
Yasakawa Motor, Driver SG- | Mitsubishi Motor HC-,HA- |
Westinghouse Modules 1C-,5X- | Emerson VE-,KJ- |
Honeywell TC-,TK- | GE Modules IC - |
Fanuc motor A0- | Yokogawa transmitter EJA- |