MachineU > China Products > Electrical Equipment & Supplies > Industrial Controls > PLC PAC And Dedicated Controllers
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
Specifications
Brand Name :
GE
Model Number :
IC693MDL930
Place of Origin :
USA
MOQ :
1
Price :
negotiable
Payment Terms :
T/T
Supply Ability :
100
Delivery Time :
5-8 work days
Packaging Details :
New in original box
Brand :
GE Fanuc
Model :
IC693MDL930
Series :
Series 90-30
Power Type :
Output Module
Output Channels :
8
Slots :
1
Output Switching Capacity :
4 Amps
DC Operating Voltage :
5 to 30 Volts DC
AC Operating Voltage :
5 to 250 Volts AC
Description

GE FANUC IC693MDL930 , 4 Amp Isolated Relay Output Module , Series 90-30 PLC

Product Description

The GE Fanuc IC693MDL930 is a 4 Amp Isolated Relay Output module. Designed for the Series 90-30 Programmable Logic Controller, this module provides 8 normally-open relay circuits. These enable the user to control output loads. Each circuit has a 4-amp output switching capacity. Each output point on the module is isolated from the other points and each point has a separate common power output terminal.

The relay output module is able to control a variety of load devices. This includes but is not limited to indicators, motor starters and solenoids. To operate the field devices connected to this module, the user needs to supply either AC or DC power. On the top of the module there are two horizontal rows of green LEDs that indicate the ON/OFF status of each point. There are eight LEDs in each row. As the IC693MDL930 only has 8 relay circuits, the bottom row is not used. The top row, which is labelled A1, indicates the status of points 1 through 8.

There is an insert that sits between the inner surface and outer surface of the hinged door on the module. On the outer left edge, the insert is colored red. This indicates that it is a high-voltage module. When the door is closed, the inner surface facing the inside of the module has circuit wiring information. On the outside surface, circuit identification information can be recorded. Users who want to implement this module for their industrial applications can do so with any Series 90-30 PLC system. The relay output module may be installed in any I/O slot of either a 5-slot or 10-slot baseplate.

Technical Specifications

Rated Voltage: 24 volts DC or 120/240 volts AC
# of Outputs: 8
Freq: 50/60 Hz with AC
Output Current: 4 Amps per circuit
Output Voltage Range: 5 to 30 volts DC, 5 to 250 volts AC
DC Power: Yes

Technical Information

Rated Voltage 24 volts DC, 120/240 VAC (nominal - see the following table for exceptions)
Operating Voltage 5 to 30 volts DC
5 to 250 VAC, 50/60 Hz
Outputs per Module Eight isolated outputs
Isolation:
Field to Backplane and to Frame Ground

250 VAC continuous;

1500 VAC for 1 minute
Point to Point 250 VAC continuous; 1500 VAC for 1 minute
Maximum Load 4 Amps resistive maximum per output
2 Amps pilot duty per output

20 Amps maximum per module for UL installations

Maximum Load depends on the ambient temperature as shown below
Minimum Load 10mA
Maximum Inrush 5 Amps
On Response Time 15ms maximum1
Off Response Time 15ms maximum1
Power Consumption 6mA (all outputs on) from 5 volt bus on backplane
70mA (all outputs on) from relay 24V bus on backplane
1 When this module is used with DC power supply IC695PSD040 or PSD140, special precautions should be taken because dropouts in the source voltage will be seen by this module and may cause relay dropouts.

GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC

GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC

Product tags

omron relay 24vdc

,

24vdc relay module

,

omron 24vdc relay
Send your message to this supplier
Send Now

GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC

Ask Latest Price
Product Detail
Brand Name :
GE
Model Number :
IC693MDL930
Place of Origin :
USA
MOQ :
1
Price :
negotiable
Payment Terms :
T/T
Contact Supplier
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC
GE FANUC IC693MDL930 4 Amp Isolated Relay Output Module Series 90-30 PLC

Shenzhen Wisdomlong Technology CO.,LTD

Verified Supplier
8 Years
guangdong, shenzhen
Since 2010
Business Type :
Importer, Exporter, Trading Company, Seller
Main Products :
Industrial Servo Motor, Industrial Servo Drives, AC Servo Amplifier
Total Annual :
1000000-5000000
Employee Number :
100~120
Certification Level :
Verified Supplier
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products Digital I O Module
MachineU China Products Electrical Equipment & Supplies Industrial Controls PLC PAC And Dedicated Controllers
Contact Supplier
Submit Requirement