7262 TDS-EN-R.pdf

Huitian^® 7262 is a one-component thread-locking anaerobic adhesive that features thixotropy, medium-high strength, and excellent resistance against fluid. The product cures when confined in the absence of air between close-fitting metal surfaces.

Typical Application

Permanent locking of thread-locking below M20 can be widely used for locking and sealing parts with large force.

Red Screw Thread Locking Adhesive 7262 replacing Loctite 262 for under M20 thread locker

Properties before curing

Typical value Range

Appearance Red liquid

Chemical type Methacrylate

Viscosity (mPa·s)

(GB/T2794-1995)

Brookfield RVT

3#spindle 2.5rpm 5,000~8,500 thixotropy

20 rpm 1,800~2,400 thixotropy

Density (g/cm³) 1.10 1.00-1.15

(GB/T13354-1992)

Flash point (℃) ＞93

(SH/T0733-2004)

Max filling gaps (mm) 0.13

Fixture time (min) ≤20

Properties after curing

Curing time at RT (h) 24

Breakaway torque (N·m) 22 14.1~28.2

Carbon steel natural color bolt (GB/T18747.1-2002)

Average dismounting torque (N·m) 30 16.9~33.9

Carbon steel natural color bolt (GB/T18747.1-2002)

Working temperature (℃) -50~150

Chemical/solvent resistance

Aged under conditions indicated and tested @ 22°C

Solvent Temperature (℃) % of initial strength

100h 500h 1000h 5000h

Engine oil 125 90 80 75 75

Leaded petrol 22 95 90 90 90

Brake fluid 22 100 100 100 100

Ethanol 22 90 90 75 75

Acetone 22 85 85 80 80

Water/glycol 87 100 70 65 60

(50%/50%)

Directions for use

Clean-up: For best results, clean all surfaces (external and internal) with a Huitian 7755 cleaning solvent and allow to dry.

Gluing: Apply glue evenly to the thread engagement area, with sufficient glue to fill the thread gap, and tighten in one pass as required by the specification. Curing speed slows down as the gap increases If the cure speed is too slow, spray all threads with Activator 7769 and allow to dry.

Assembly: Shake the product thoroughly before use. To ensure that the system achieves maximum performance, the recommended curing time is 24 hours or more to ensure that the adhesive layer is fully cured.

Cautions

Not suitable for use on plastic parts, not suitable for use in pure oxygen and oxygen-rich systems, and not for sealing chlorine or other strong oxidizing substances.

Store unused glue in a sealed container for next use. Contaminated glue should not be refilled into the original bottle as this may affect the performance of the remaining glue.

This product contains acrylic and methacrylate substances which are irritating to the skin and eyes. Recommended for use in a ventilated area. In case of accidental contact with eyes and skin, rinse immediately with water.

Keep away from children for storage.

For safe handling information on this product, consult the Safety Data Sheet (SDS).

Packing specification

Order code: 726201, 50ml/tube, 10 pcs/carton, 80 pcs/box

726203, 250ml/bottle, 10 pcs/carton

Storage

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.

Shelf life is 18 months

We can also make:

1. Low strength & thixotropic thread locker

2. Middle strength & thixotropic thread locker

3. High strength & oil resistant thread locker

4. High strength & chemical resistant thread locker

5. High strength & thixotropic thread locker

6. High strength & high viscosity thread locker

7. High strength & middle viscosity thread locker

8. High-strength & high-temperature resistant thread locker

9. High strength & fast osmotic thread locker

Performance of thread locker and sealant anaerobic adhesive/pre-coated thread locker and sealant anaerobic adhesive

Note: *Viscosity - measured at Brookfield RVF 20rpm: *2 # rotor **3 # rotor ***4 # rotor ****5 # rotor

Our Advantages:
1. Listed company in China (stock code: 300041)
2. Famous Trademark of China
3. Fast Delivery
4. OEM services/small orders are welcome