AM3352BZCZD80 MPU ARM Cortex-A8 32Mbit 800 MHz 1.26V PBGA-324

Features

• Up to 1-GHz Sitara™ ARM® Cortex® -A8 32‑Bit RISC Processor

– NEON™ SIMD Coprocessor

– 32KB of L1 Instruction and 32KB of Data Cache With Single-Error Detection (Parity)

– 256KB of L2 Cache With Error Correcting Code (ECC)

– 176KB of On-Chip Boot ROM

– 64KB of Dedicated RAM

– Emulation and Debug - JTAG

– Interrupt Controller (up to 128 Interrupt Requests)

• On-Chip Memory (Shared L3 RAM)

– 64KB of General-Purpose On-Chip Memory Controller (OCMC) RAM

– Accessible to All Masters

– Supports Retention for Fast Wakeup

• External Memory Interfaces (EMIF)

– mDDR(LPDDR), DDR2, DDR3, DDR3L Controller:

– mDDR: 200-MHz Clock (400-MHz Data Rate)

– DDR2: 266-MHz Clock (532-MHz Data Rate)

– DDR3: 400-MHz Clock (800-MHz Data Rate)

– DDR3L: 400-MHz Clock (800-MHz Data Rate)

– 16-Bit Data Bus – 1GB of Total Addressable Space

– Supports One x16 or Two x8 Memory Device Configurations

– General-Purpose Memory Controller (GPMC)

– Flexible 8-Bit and 16-Bit Asynchronous Memory Interface With up to Seven Chip Selects (NAND, NOR, Muxed-NOR, SRAM)

– Uses BCH Code to Support 4-, 8-, or 16-Bit ECC

– Uses Hamming Code to Support 1-Bit ECC

– Error Locator Module (ELM)

– Used in Conjunction With the GPMC to Locate Addresses of Data Errors from Syndrome Polynomials Generated Using a BCH Algorithm

– Supports 4-, 8-, and 16-Bit per 512-Byte Block Error Location Based on BCH Algorithms

• Programmable Real-Time Unit Subsystem and Industrial Communication Subsystem (PRU-ICSS)

– Supports Protocols such as EtherCAT® ,PROFIBUS, PROFINET, EtherNet/IP™, and More

– Two Programmable Real-Time Units (PRUs)

– 32-Bit Load/Store RISC Processor Capable of Running at 200 MHz

– 8KB of Instruction RAM With Single-Error Detection (Parity)

– 8KB of Data RAM With Single-Error Detection (Parity)

– Single-Cycle 32-Bit Multiplier With 64-Bit Accumulator

– Enhanced GPIO Module Provides ShiftIn/Out Support and Parallel Latch on External Signal

– 12KB of Shared RAM With Single-Error Detection (Parity)

– Three 120-Byte Register Banks Accessible by Each PRU

– Interrupt Controller (INTC) for Handling System Input Events

– Local Interconnect Bus for Connecting Internal and External Masters to the Resources Inside the PRU-ICSS

– Peripherals Inside the PRU-ICSS: – One UART Port With Flow Control Pins, Supports up to 12 Mbps

– One Enhanced Capture (eCAP) Module

– Two MII Ethernet Ports that Support Industrial Ethernet, such as EtherCAT

– One MDIO Port • Power, Reset, and Clock Management (PRCM) Module

– Controls the Entry and Exit of Stand-By and Deep-Sleep Modes

– Responsible for Sleep Sequencing, Power Domain Switch-Off Sequencing, Wake-Up Sequencing, and Power Domain Switch-On Sequencing

– Clocks

– Integrated 15- to 35-MHz High-Frequency Oscillator Used to Generate a Reference Clock for Various System and Peripheral Clocks

– Supports Individual Clock Enable and Disable Control for Subsystems and Peripherals to Facilitate Reduced Power Consumption – Five ADPLLs to Generate System Clocks (MPU Subsystem, DDR Interface, USB and Peripherals [MMC and SD, UART, SPI, I 2C], L3, L4, Ethernet, GFX [SGX530], LCD Pixel Clock)

Functional Block Diagram

Specifications

Trading Guides