Advanced HDPE Textured Geomembrane For Slope Anti-Slip And Anti-Seepage Solutions
Product Introduction
Cylindrical point rough geomembrane is a high performance geosynthetic material that provides additional friction and adhesion by forming special column points or textures on the surface of the geomembrane.
Product Properties
1. High coefficient of friction: The column point design significantly improves the coefficient of friction between the geomemofilm and soil or other materials, helping to prevent sliding in slope or vertical applications.
2. Enhanced adhesion: The column point structure enhances the adhesion of the geomembrane and is suitable for applications where additional stability is required.
3. Excellent impermeability: Inherited the core advantages of high-density polyethylene (HDPE) geomemofilm, effectively preventing the penetration of water and pollutants.
4. Chemical resistance: It has good resistance to most chemical substances and is suitable for use in a variety of environmental conditions.
5. Resistance to environmental stress cracking: Excellent resistance to environmental stress cracking, able to maintain stability in harsh environments.
6. Temperature adaptability: It has good heat resistance and cold resistance and can be used in a wide temperature range.
Product Application
1. Slope engineering: Suitable for slope anti-seepage engineering where stability is required, especially in steep or unstable terrain.
2. Landfill: used for slope anti-slip and anti-seepage of landfill to improve the safety and environmental protection of the project.
3. Tailings pond: used in the seepage prevention and stabilization project of tailings pond to prevent the leakage of harmful substances.
4. DAMS and reservoirs: Used for seepage prevention and reinforcement of DAMS and reservoirs to improve the durability of the structure.
Products series
Single textured geomembrane, double-wall textured geomembrane.
Product Specification
* Thickness(mm): 0.30mm~3.00mm
* Width: 4m~8m
* Roll length: 50m~100m (customized request accept)
PS: Customized request accept for all above.
Geomembrane Series
Textured HDPE Geomembrane For Landfill (GB/T 17643-2011(GH-2T1,GH-2T2))
|
(CJ-T234-2006)
Specification | 1.00mm | 1.25mm | 1.50mm | 2.00mm | 2.50mm | 3.00mm | Remark | |
Item | ||||||||
Thickness (mm) | 1.00mm | 1.25mm | 1.50mm | 2.00mm | 2.50mm | 3.00mm | ||
Textured Highth (mm) | 0.25 | |||||||
Density (g/c㎡,≥) | 0.94 | |||||||
Tensile Properties | ||||||||
Yield Strength (N/mm,LD/TD) | 15 | 18 | 22 | 29 | 37 | 44 | ||
Breaking Strength (N/mm,LD/TD) | 10 | 13 | 16 | 21 | 26 | 32 | ||
Yeild Elongation Rate (%) | 12 | |||||||
Breaking Elongation Rate (%) | 100 | |||||||
Rectangular Tear Strength (N) | 125 | 156 | 187 | 249 | 311 | 374 | ||
Puncture Strength (N) | 267 | 333 | 400 | 534 | 667 | 800 | ||
Environmental Stress Crack Resistance (h) (A single point of incision constant tensile method) |
300 | |||||||
Carbon Black | ||||||||
Carbon Black Content(Rang) (%) | 2.0~3.0 | |||||||
Carbon Black Dispersion | Nine of 10 observation area should be grade 1 or grade 2, not more than 1 of grade3 | |||||||
Oxidative Induction Time (OIT) | ||||||||
Standard OIT (min) | 100 | |||||||
High Pressure OIT (min) | 400 | |||||||
85℃ Oven Ageing (Minimum Average) | ||||||||
90 days after baking, the standard OIT retention(%) | 55 | |||||||
90 days after baking, the hight pressure OIT retention(%) | 80 | |||||||
The Anti-UV Strength | ||||||||
Ultraviolet irradiation after 1600 hours, the standard OIT retention(%) | 50 | |||||||
Ultraviolet irradiation after 1600 hours, the high pressure OIT retention(%) | 50 | |||||||
-70℃ The Low Temperature Embrittlement Performance mpact | Pass | |||||||
Water Vapor Penetration Coefficient g.cm (cm2.s.Pa) | ≤1.0X10-13 | |||||||
Dimensional Stability | ±2 |