Model No. : TXW700028N0
Features
Item | Specification |
LCD size | 7.0 inch(Diagonal) |
Driver element | a-Si TFT active matrix |
Resolution | 1024*3RGB(H)X600(V) |
Display mode | Normally white, Transmissive |
Dot pitch | 0.1506*0.1432mm |
Active area | 154.21(H) * 85.92(V)mm |
Module size | 164.9*100*3.5mm |
Surface treatment | Anti-Glare |
Color arrangement | RGB-stripe |
LCM Driver IC | HX8282A11 |
Backlight current | 200-280mA |
Lumens degrees | 800cd/m² |
7" TFT 1024x600 dots Product Drawing
Module Function Description
Pin No. | Symbol | LCM Description |
1 | LEDA | Power Supply For LED Backlight Anode Input. |
2 | LEDA | Power Supply For LED Backlight Anode Input. |
3 | LEDK | Power supply for backlight cathode input terminal. |
4 | LEDK | Power supply for backlight cathode input terminal. |
5 | GND | Power ground |
6 | VCOM | Common Voltage |
7 | DVDD | Power for Digital Circuit 3.3V |
8 | MODE | DE/SYNC mode select. MODE=H:DE mode;MODE=L:SYNC mode |
9 | DE | Data enable signal in RGB I/F mode 1 |
10 | VS | Vertical sync. Signal in RGB I/F |
11 | HS | Horizontal sync. Signal in RGB I/F |
12~19 | B7~B0 | 8 bit data bus display blue data |
20~27 | G7~G0 | 8 bit data bus display green data |
28~35 | R7~R0 | 8 bit data bus display red data. |
36 | GND | Power ground |
37 | DCLK | Pixel clock signal in RGB I/F |
38 | GND | Power ground |
39 | L/R | Left / right selection |
40 | U/D | Up/down selection |
41 | VGH | Gate ON Voltage |
42 | VGL | Gate OFF Voltage |
43 | AVDD | Power for Analog Circuit |
44 | RESET | Global reser pin |
45 | NC | No connection |
46 | VCOM | Common Voltage |
47 | DITHB | Dithering function. Dithering function. DITHER = H:Enable internal dithering function; |
48 | GND | Power ground |
49 | NC | No connection |
50 | NC | No connection |
Absolute Maximum Rating
Characteristics | Symbol | Min. | Max. | Unit |
LCM Operating Temperature | TOPR | -20 | +70 | °C |
LCM Storage Temperature | TSTG | -30 | +80 | °C |
Humidity | RH | 10 | 90 | % |
TFT DC Characteristics
Characteristics | Symbol | Min. | Typ. | Max. | Unit | Note |
TFT OperationFrame rate | Hz | -- | 60 | -- | Hz | |
Supply Voltage for(DC/DC) | VDD | 3.0 | 3.3 | 3.6 | V | |
TFT Gate ON Voltage | VGH | 17 | 18 | 19 | V | Note 2 |
TFT Gate OFF Voltage | VGL | -6.5 | -6 | -5.5 | V | Note 2 |
TFT Common Voltage | Vcom | 3.0 | 3.15 | 3.3 | V | Note 1 |
AVDD | Avdd | 8.9 | 9.0 | 9.1 | V | Note 3 |
Note 1: VCOM value should be adjusted by different condition to optimize Flicker Value.
Note 2: VGH and VGL are the operating voltages of TFT gate.
Note 3: Adjust the contrast, make the color bigger and darker, and make the color smaller and lighter.
Back-Light Unit Characeristics
The back-light system is an edge-lighting type with 30 white LEDs. The characteristics of the back-light are shown in the following tables.
Characteristics | Symbol | Min. | Type | Max. | Unit | Notes |
Forward Voltage | VF | 8.8 | -- | 10 | V | - |
Forward current | IF | -- | 200 | -- | mA | - |
Luminance(With LCD+CTP) | Lv | -- | 650 | -- | cd/m2 | - |
LED life time | N/A | -- | 30,000 | -- | Hr | Note 1 |
Note:
The “LED life time” is defined as the module brightness decrease to 50% of original brightness at IL=20mA/LED. The LED life time could be decreased if operating IL is larger than 25mA/LED
Reliability Test Item
No. | Test Item | Test Condition | Notes |
1 | High Temp. Storage | +80°C / 96H | 1. Functional test isOK. Missing Segment,short, unclear segment non-display,display abnormally and liquid crystal leakare un-allowed. 2. No low temperature bubbles,end seal loose andfall, frame rainbow.
|
2 | Low Temp. Storage | -30°C / 96H | |
3 | High Tempe. Operating | +70°C / 96H | |
4 | Low Tempe. Operating | -20°C / 96H | |
5 | High Temperature /Humidity storage | 60°C x 90%RH /96H | |
6 | Thermal and cold shock | Static state, -20℃(30min) ~70℃ (30min),50 cycles |
7" TFT 1024x600 dots Product Image