5mm round pure green color Indicator LED in 9.Back lighting outdoor advertising Circuit board

• Features:

• Choice of various color.
• Available on tape and reel.
• Reliable and robust.
• The product itself will remain within RoHS compliant Version.

• Descriptions:

• The series is specially designed for applications requiring higher brightness.
• The LED lamps are available with different colors, intensities.

• Applications:

• TV set.
• Monitor.
• Telephone.
• Computer.
• Circuit board.
• Status indicators.
• Commercial use.
• Advertising Signs.
• Back lighting.

• Package Dimension:

  Notes:

• All dimensions are in millimeters (inches).
• Tolerance is ± 0.25 mm (.010″) unless otherwise noted.
• Protruded resin under flange is 1.00 mm (.039″) max.
• Specifications are subject to change without notice.
• Absolute Maximum Ratings at Ta=25℃

• Parameters	Symbol	Max.	Unit
  Power Dissipation	PD	120	mW
  Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width)	IFP	100	mA
  Forward Current	IF	30	mA
  Reverse Voltage	VR	5	V
  Operating Temperature Range	Topr	-40℃ to +85℃
  Storage Temperature Range	Tstg	-40℃ to +100℃
  Lead Soldering Temperature [4mm (.157″) From Body]	Tsld	260℃ for 5 Seconds

  Electrical Optical Characteristics at Ta=25℃

  Parameters	Symbol	Min.	Typ.	Max.	Unit	Test Condition
  Luminous Intensity *	IV	14000	23000	---	mcd	IF=20mA (Note 1)
  Viewing Angle *	2θ1/2	---	20	---	Deg	IF=20mA (Note 2)
  Peak Emission Wavelength	λp	---	518	---	nm	IF=20mA
  Dominant Wavelength	λd	---	523	---	nm	IF=20mA (Note 3)
  Spectrum Radiation Bandwidth	Δλ	---	35	---	nm	IF=20mA
  Forward Voltage	VF	3.0	3.3	4.0	V	IF=20mA
  Reverse Current	IR	---	---	10	µA	VR=5V

  Notes:

• Luminous Intensity Measurement allowance is ± 10%.
• θ_1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
• The dominant wavelength (λd) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device.

• Typical Electrical / Optical Characteristics Curves

(25℃ Ambient Temperature Unless Otherwise Noted)

• Reliability Test Items And Conditions:

The reliability of products shall be satisfied with items listed below:

Confidence level: 90%. LTPD: 10%.

1) Test Items and Results:

2) Criteria for Judging the Damage:

• Please read the following notes before using the product:

1. Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.

2.5 The LEDs should be used within 168 hours (7 days) after opening the package.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

4. Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 260℃ for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder.

5. Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

6. Caution in ESD

Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices equipment and machinery must be properly grounded.