Function | VM-3004-HYBRID | |
System | Language | English / Chinese |
Operation Interface | Graphical User Interface (OSD menu) | |
Password Security | 2 Levels: Administrator & User | |
Video | Video Input | Supports 4 channels 1080P AHD camera Video input Supports 4 channels CIF/HD1/D1/960H/720P AHD camera Video input Supports 4 channels 1080P/720P IP camera Video input Supports 4-CH 1080P/720P IPC + 4-CH 720P AHD/960H/D1/CIF Video input |
Video Output | 1 each HDMI (max. 1080P), 2 CVBS (Analog); 1 each 3.5mm Jack on Front Panel and one connection on the 24 pin I/O port | |
Video Display | Single picture, 1~8 pictures | |
Signal System | PAL / NTSC ( PAL@200 frame 1080P/sec; NTSC@240 frame 1080P/sec ) | |
Image Compression | H.264 Main profile | |
Audio | Audio Input | 4 Channels |
Audio Output | 2 Channels (Front Panel 3.5mm Jack, 1 in the 24pin connector) | |
Record Format | Synchronized A/V recording | |
Recording & Storage | Image Resolution | CIF / HD1 / D1 / 960H / 720P /1080Poptions |
Video Coding | ISO14496-10 Industry Standard | |
Video Bit Rate | CIF: 1536Kbps ~ 128Kbps, | |
HD1/D1: 2048Kbps ~ 400Kbps, | ||
960H: 2048Kbps ~ 400Kbps, | ||
720P:4096Kbps ~ 400Kbps | ||
1080P:4096Kbps ~ 400Kbps | ||
Select from 8 Levels of Video Image Quality ranging from 1(Highest) to 8(Lowest) | ||
Audio Bit Rate | 40Kbps | |
Storage | Up to 2TB HDD/SSD and 1 SD card for backup(at 3G/4G/WIFI model option) | |
Alarm | Alarm Input | 8 Channels, Select Trigger for either less than 1VDC or greater than 5VDC |
Alarm Output | 1 Channel, 12V output | |
Communication Ports | RS485 | 1 Port for PTZ control or Data Device usage |
RS232 | 2 Port for communication or data usage | |
RJ45 Network | 4 Ports of RJ45, For connection to an IP camera with maximum of 1080P | |
USB | 2 Ports of USB 2.0, the front is used to export record file. The rear panel is used to mirror | |
Wireless Communication* | 3G* | 3G (HSUPA / HSDPA / WCDMA / EVDO / TD-SCDMA) optional Internal module |
4G* | 4G (TDD-LTE / FDD-LTE) optional module to match local cellular carrier | |
Wi-Fi* | Internal Wi-Fi 802.11b/g/n ( 2.4 / 5.8 Ghz) optional | |
GPS* | Int'l Standard GPS* | Internal GPS module. Real-time geographic coordinates, speed information |
G-Sensor | Internal G-Sensor | Supports 3 Axis Motion Detection with user set ranges, for X, Y and Z coordinates |
Software | PC Playback | A/V, GPS, Mapview, Speed, G-Sensor, etc. files available for playback on PC. Limited playback is also available on MDVR |
IVMS | Wireless (require Wi-Fi or cellular Option) real-time A/V monitoring, GPS, alarms, etc. | |
Software Upgrade | Local or Remotely | Upgrade through the front USB2.0 or remotely via IVMS platform |
Voltage Input | +8~+36V | 8~36VDC Please check operational voltage of vehicle prior to the installation of the MDVR and its accessories to prevent possible damage |
Voltage Output | 12V | 12V(+/-0.2V),Max 3A |
ACC Detection | ≤4V | Power Off |
≥6V | Power On | |
Video Input Resistance | 75Ω | 75Ω |
Video Output Voltage | 2Vp-p | 2VP-P CVBS output analog signal, screen input requires 75Ω resistance |
I / O port | <1V | Low voltage trigger |
>5V | High voltage trigger | |
Operation Temperature | -40℃~80℃ | Install in well ventilated area, protected from moisture, heat, dust and vibration |
Dimensions | 192x184x61mm | Including Security Cover 248x184x61mm |
Q: 3G/4G signal is intermittent and video is not smooth
A: So far, WCDMA and EVDO has good coverage (4G is desired to be improved). In case where signal is not covered in some mountainous areas or signal is weak due to local network restrictions in some suburban areas, the video may not be smooth or even cannot be viewed. In this case, it is largely affected by the local network; in addition, check if the frame rate for the sub stream is set too high. This may occur when the network condition is poor while the frame rate is high.
Q: Connection is impossible even when WiFi signal is up to -60db
A: If your WiFi is correctly set, connection is generally not a problem when signal intensity is up to -60db. If the device cannot be found within LAN, check if SSID and password are correctly set. Of course, the IP address shall be properly set; in addition, check the encryption type and authentication mode are set to requirements.