1785-L60L

The 1785-L60L is a member of the PLC-5 controller series. This programmable controller can function as a central part of any control system based on the PLC-5 series. The 1785-L60L is the central point that interconnects local, extended, and remote I/O modules on different types of communication interfaces, and which acts as the backbone of the control system. The 1785-L60L controller has three integrated communication interfaces marked as Channel 1A, Channel 1B, and Channel 2. Channel 1A and Channel 1B can function as remote I/O scanners, remote I/O adapters, or as DH+ communication interfaces. The third communication interface on the 1785-L60L, Channel 2, is an extended-local I/O port. The 1785-L60L controller has a 25-pin connector marked as Channel 0 on the front panel. Channel 0 is an optically-isolated EIA RS232C port, which supports ASCII and DF1 full-duplex and half-duplex master protocols as well as half-duplex slave protocols. Channel 0 has a green light for indicating the status of the communication interface. In addition, there is one 8-pin mini DIN connector marked as Channel 1A, which is a DH+ programming terminal connection parallel to Channel 1A. Two three-pin connectors are on a lower part of the front panel. These connectors are for Channels 1A and 1B, and these two communication ports can function as remote I/O scanners, remote I/O adapters, or as DH+ communication ports. On the 1785-L60L’s front panel, there is special connector marked as Channel 2, which is for an extended local I/O contact.

Remote I/O Scanner Mode reads and writes I/O information between the controller and the remote I/O device. When used as an I/O scanner, the 1785-L60L is a supervisory controller for the other controllers in Adapter Mode and for the other remote I/O adapters. When either Channel 1A or Channel 1B is configured as a remote I/O adapter, the 1785-L60L controller manages the controller-resident I/O while communicating with the supervisory controller through a remote I/O link. A DH+ link can be configured on either Channel 1A or 1B on the 1785-L60L. DH+ communication is used for creating a peer-to-peer network with other PLC-5 controllers or other higher-level components of the control system. Programming of the 1785-L60L controller can be also done via a DH+ link. By using a DH+ link, multiple controllers can be programmed at the same time. The maximum cable length for a DH+ link depends on the transmission rate. It is important that all devices on the link are configured to communicate at the same rate. That length ranges from 3048m from a speed of 57.6 kilobits per second to 762m for a speed of 230.4 kilobits per second. An extended local I/O link is useful when more I/O than what can fit in single chassis is necessary, but it requires greater speed than a remote I/O link can provide. The 1785-L60L and extended local I/O adapter (the 1771-ALX) installed in the remote I/O chassis interconnected with the I/O link cable form an extended-local I/O link. The extended local I/O link is limited to 100 feet of cable. If the I/O chassis needs to be further from the controller, use the remote I/O link. The extended local I/O link is a parallel link that enables the 1785-L60L controller to scan a maximum of 16 extended I/O chassis. Scan time per rack on an extended – local I/O is 0.5 ms. The 1785-L60L has several indicators on the front panel to make user interface easy. The indicators display various controller statuses. The indicator marked BATT displays the battery status. The PROC indicator shows the current controller mode. For example, it is green when the controller is in RUN Mode, and red when something is wrong. The FORCE indicator is amber when the I/O forces are enabled. The COMM indicator is linked to the Channel 0 communication status. Communication Channels 1A and 1B both have dedicated status indicators. Channel 2, used for extended – local I/O connection, has a dedicated status indicator.

Our Main Products


① (USA AB) series of products: 1756-IB32, 1769-OF5, 1747-L552, 1746-OW8, 1785-L60B, 1756-L73S

② Schneider (France) products: 140CPU65160, 140CPU31110, 140CPU11302, 140CPU21304, 140CPU67160, 140CPU53414A

③ General Electric (USA) series of products: IC697ALG230, IC694MDL754, IC697MDL750, IC693MDL640, IC693CPU313

④ Ovation (USA) series of products: 5X00226G02, 1C31222G01, 1C31179G02, 1C31150G01, 1C31194G03, 1C31192G01

⑤ Honeywell (USA): CC-TDOR01, 8C-TDODA1, 8C-PAIMA1, CC-TAOX11, 8C-PAIH54, CC-PCNT01, 8C-PDISA1, 8C-PDILA1

⑥ Sales ABB (Sweden): D0910S, AO920, AO810, 07KT98, 07KT97, CMA132 3DDE300412, DO820, DI920, DSQC663

⑦ Invensys Triconex (USA): 4329, 4351B, 3008, 8311, 8310, 3501E, 4352A, 8305A, 3502E, 3504E, 3805E, 3503E

⑧ Invensys Foxboro I / A Series system (USA): FBM219, CP40, ZCP270, CP60, FBM231, FCP270, FBM215, P0922AE

⑨ Siemens (Germany): 6ES7414-2XG03-0AB0, 6DD1601-0AE0, 6DD1681-0AH2, 6ES5491-0LB11, 6ES7414-4HJ04-0AB0, 505-4732, 6ES5451-4UA13, 505-6208

About Our Team

New Source Automation Co., Ltd is a leading supplier of Original brand new PLC & DCS parts, you can find below brands: Allen Bradley, Omron, Schnerder, Siemens, ABB,Rosemount,Yokogawa,Honeywell, Bently Nevada, GE,

Hima,Woodward, Prosoft, Foxboro, Emerson etc.With tens of thousands of new parts in stock, we have exported to more than 50 countries in the world. Excellent quality,sincere service and quick delivery make us grow rapidly. Our main products types are PLC and DCS Processing Module, Power Supply Module, Input Module, Output Module, I/O Module, Rack, Panels, Proximitor Sensor, Programming Cable,Terminal Blocks etc. Any of your demands and inquiry, big or small, will be highly valued.

Packing & Delivery

1)100% brand New and Original Factory Seal!
2)Warranty: 1 year
3)Package: Original packing with cartons.
4)Delivery time: DHL,UPS,Fedex express shipping usually take 3-10 working days,depends on the country delivered to. In rare cases,the strict custom clearances will make the delivery time a bit longer,please be patient.
5) All the goods will be tested before shipment.