MachineU > China Products > Office & School Supplies > Printer Supplies > Fuser Film Sleeves
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
Specifications
Brand Name :
HUASHIDA
Certification :
ISO9001
Place of Origin :
Qingdao，Shandong，China
MOQ :
1
Payment Terms :
L/C, D/A, D/P, T/T, Western Union, MoneyGram
Delivery Time :
10workdays
specific density :
0.935r/cm3
tensile strengt :
38 Mpa
Elongation at break :
385%
water-intake rate :
0.05%
peel strength :
>150N/cm
Description

3pe Coating pipe Joints Heat shrinkable sleeve,PE Pipe Wrap Around Sleeve

HUASHIDA Heat shrinkable sleeve Widely used in thermal insulation pipe joint sealing anticorrosion waterproof end cap, municipal drainage and sewage pipe connection mending, inspection wells, steel belt reinforced spiral corrugated pipe, especially for the size of the head, anticorrosive sealing, to solve the drag pipe, corrugated pipe heat-shrinkable tape mending products contraction not to the end of the problem!

Thickness of 1.8/2.0/2.5/3.0mm according to different environments to choose different products.
Width 80-800mm can be customized.

ITEM Standard UNIT Data
Adhesive softening point ASTM E 28 °C 70-80
shear strength DIN 30 672 N/cm ≥100
Basic specific density ASTM D792 r/cm 3 0.935-0.96
tensile strength ASTM D638 Mpa 15-20
Elongation at break ASTM D792 % 350
hardness ASTM D2240 ball 48
Heat Shrinkable Sleeve peel strength ASTM D1000 N/cm >150
water-intake rate ASTM D570 % 0.05

3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa

Move the heat shrink sleeve to the centered position at the joint and take out the isolation material. Heat evenly from the center along the circumference, make it shrink completely and then extend the heating to both ends respectively. Pay attention to the even fire. After all the shrinkage is completed, reheat the uneven surface to make it completely flat. After the overall heating is completed, turn down the flame and reheat again to make the hot melt adhesive fully overflow. During the heating process, use the pressure roller to roll the joint several times, focusing on rolling the fusion lap to eliminate air bubbles.
Feature
1.Fast shrinkage speed,
2.good waterproof performance,
3 good anti-corrosive performance,
4.long service life, convenient transportation and fast construction.
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa


2. 3Layer Fiber

reinforced PE heat shrinkable tape (sleeve) is composed of cross-linked polyethylene back, a middle layer of fiber and special heat melt adhesive an. The 3 layer reinforced sleeve gives better shrink ratio, and better strength. It is resistant to corrosion, wear, impact, UV and aging, easier to be operated.
Application area:
It is mainly used for Hollow wall spiral pipe, corrugated pipe and metal reinforced corrugated spiral pipe etc.

TEST PROCEDURE
1. Clean the steel pipe and heat it by fire till over 80 ºC
2. Paint the steel pipe with Primer (mixed with A&B)
3. Fire heat the heat shrink sleeve, be attention to start heating from middle of the sleeve, but act from up and down, and gradually move from middle to two sides of sleeve, in order to drive air out of the sleeve, after finish heating, the good result is that there is about 1-2mm hot adhesive melt at the edge of sleeve.
TEST RESULT
1. Test result after cooling about 40 minutes.
Peel strength to primer is over 100N per 2cm(till the end of the spring balance). at 30.7ºC
Co-adhesive: Half-half.
2. Test result after cooling about 24hours.
Peel strength to primer is over 172N per 2cm at room temperature about 30.7ºC
Co-adhesive: Half-half.
3. 2. Test result after cooling about 24hours.
Peel strength to primer is over 9.2kg/90N per 1cm at room temperature about 30.7ºC
Co-adhesive: Half-half.

3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa

Send your message to this supplier
Send Now

3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa

Ask Latest Price
Watch Video
Product Detail
Brand Name :
HUASHIDA
Certification :
ISO9001
Place of Origin :
Qingdao，Shandong，China
MOQ :
1
Payment Terms :
L/C, D/A, D/P, T/T, Western Union, MoneyGram
Delivery Time :
10workdays
Contact Supplier
video
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa
3pe Coating pipe Joints Heat shrinkable sleeve PE Pipe Wrap Around Sleeve 38 Mpa

Qingdao Huashida Machinery Co., Ltd.

Verified Supplier
2 Years
shandong, qingdao
Since 2003
Business Type :
Manufacturer
Main Products :
Pre-Insulated Pipe Production Line, 3LPE Coating Pipe Production Line, Polyurethane Spraying Foam Preinsulated Steel Pipe Making Machine
Total Annual :
3000000-5000000
Employee Number :
100~200
Certification Level :
Verified Supplier
Discover similar products
View More

Find Similar Products By Category:

Supplier Homepage Products Heat Shrinkable Sleeve
MachineU China Products Office & School Supplies Printer Supplies Fuser Film Sleeves
Contact Supplier
Submit Requirement