I/O module

X20 energy measurement and synchronization module

B&R ID code

0x2433

Status indicators

Channel status, operating state, module status

Diagnostics

Module run/error

Yes, using LED status indicator and software

Analog inputs

Yes, using LED status indicator (measurement range of analog inputs)

Digital outputs

Yes, using LED status indicator and software

Overvoltage category

ll

Power consumption

Bus

1.4 W

Internal I/O

4 W

Additional power dissipation caused by actuators (resistive) [W]

-

Certifications

CE

Yes

UKCA

Yes

ATEX

Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X

UL

cULus E115267
Industrial control equipment

HazLoc

cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5

KC

Yes

Quantity

5

Variant

Current-sourcing FET

Nominal voltage

24 VDC

Switching voltage

24 VDC -15% / +20%

Nominal output current

0.1 A

Total nominal current

0.5 A

Connection type

1-wire connections

Output circuit

Source

Output protection

Thermal shutdown in the event of overcurrent or short circuit

Diagnostic status

Output monitoring with 10 ms delay

Leakage current when the output is switched off

5 μA

Residual voltage

<0.3 V at 0.1 A nominal current

Peak short-circuit current

<2 A

Switch-on in the event of overload shutdown or short-circuit shutdown

Approx. 10 ms, depends on the module temperature

Switching delay

0 → 1

<300 μs

1 → 0

<300 μs

Switching frequency

Resistive load

Max. 100 Hz

Insulation voltage between channel and bus

500 Veff

Quantity

1

Variant

Relay / Changeover contact

Nominal voltage

30 VDC / 240 VAC

Rated frequency

DC / 45 to 63 Hz

Switching capacity

Min.

10 mA / 5 VDC

Max.

30 W / 240 VAC

Nominal output current

1 A at 30 VDC / 1 A at 240 VAC

Actuator power supply

External

Switching voltage

Max. 60 VDC / 250 VAC

Switching delay

0 → 1

≤10 ms

1 → 0

≤10 ms

Service life

Mechanical

Min. 10 x 106ops.

Electrical

Min. 60 x 103ops. (NC) at 1 A
Min. 30 x 103ops. (NO) at 1 A

Contact resistance

Max. 100 mΩ

Protective circuit

Internal

None

External

None

DC

Inverse diode, RC combination or VDR

AC

RC combination or VDR

Insulation voltage

Channel - Channel

1000 VAC / 1 min

Channel - Bus

4000 VAC / 1 min

Channels

8

Input

120 VAC / 480 VAC

Input type

Single-ended

Digital converter resolution

±15-bit

Conversion time

50 Hz

20 ms

60 Hz

16.67 ms

Permissible input signal

Max. 132 VAC / 528 VAC

Output format

±120 VAC

1 LSB = 0x0001 = 5.707 mV

±480 VAC

1 LSB = 0x0001 = 22.787 mV

Output of digital value during overload

Overshoot

0x7FFF

Undershoot

0x8001

Conversion method

SAR

Input filter

Cutoff frequency

10 kHz

Slope

60 dB

Maximum gain drift

0.02% per °C

Maximum offset drift

0.003% per °C

Crosstalk between channels

-70 dB

Nonlinearity

≤0.5% at 45 to 65 Hz

Protection against electric shock

Protective impedance per EN 61131-2

Test voltage between channel and bus (type test)

3700 Veff

Output format

INT

Input impedance in signal range

Approx. 3 MΩ

Max. error at 25°C

Gain

0.09%

Offset

0.03%

Input protection

Overvoltage protection

Channels

3

Input

1 A / 5 A AC

Input type

Isolated current transformer according to the compensation principle with a magnetic sensor, for connecting an external transformer

Digital converter resolution

±15-bit

Conversion time

50 Hz

20 ms

60 Hz

16.67 ms

Permissible input signal

Max. 1.5 A / 7.7 A

Output format

±1 A

1 LSB = 0x0001 = 189.903 μA

±5 A

1 LSB = 0x0001 = 949.513 μA

Output of digital value during overload

Overshoot

0x7FFF

Undershoot

0x8001

Conversion method

SAR

Input filter

Cutoff frequency

10 kHz

Slope

60 dB

Maximum gain drift

0.07% per °C

Maximum offset drift

0.003% per °C

Crosstalk between channels

-70 dB

Nonlinearity

≤0.5% at 45 to 65 Hz

Insulation voltage between channel and bus

500 Veff

Output format

INT

Max. error at 25°C

Gain

0.2%

Offset

0.05%

Thermal overcurrent

15 x INom for 0.2 s

Monitored overcurrent

4 x INom

Input impedance

Measurement range 1 A

Max. 30 mΩ

Measurement range 5 A

Max. 10 mΩ

Electrical isolation

Bus isolated from I/O power supply and digital inputs and outputs

Digital inputs and outputs isolated from each other

Mounting orientation

Horizontal

Yes

Vertical

Yes

Installation elevation above sea level

0 to 2000 m

No limitation

>2000 m

Reduction of ambient temperature by 0.5°C per 100 m

Degree of protection per EN 60529

IP20

Temperature

Operation

Horizontal mounting orientation

0 to 60°C

Vertical mounting orientation

0 to 50°C

Derating

See section "Derating".

Storage

-40 to 85°C

Transport

-40 to 85°C

Relative humidity

Operation

5 to 95%, non-condensing

Storage

5 to 95%, non-condensing

Transport

5 to 95%, non-condensing

Note

Order 2x terminal block X20TB12 separately.
Order 2x screw clamp terminal block TB3102 and 2x screw clamp terminal block TB3104 separately.

Pitch

87.5+0.2mm