IS200EPCTG1AAA Exciter PT/CT Terminal Board

Description

IS200EPCTG1AAA is an Exciter PT/CT (EPCT) terminal board developed by GE. It is a part of EX2100 excitation system. Exciter PT/CT (EPCT) terminal board serves as an indispensable component specifically designed to handle critical measurements of generator voltage and current via isolation transformers. This board integrates two 3-phase generator potential transformer (PT) voltage inputs and two generator current transformer (CT) inputs, offering current options of 1 A or 5 A. All output signals from the isolation transformers are efficiently cabled to the EMIO board, strategically positioned within the control rack. Additionally, EPCT accommodates a single analog input, capable of accepting either voltage or current inputs. For applications demanding the utmost reliability, the system can incorporate up to three EPCT boards, ensuring redundancy and system robustness.

• The board's functionality involves receiving generator voltages from the customer's potential transformers, directing these inputs through switches to TB1. This setup allows for cable lengths of up to 1000 ft using 12 AWG wire. The PT inputs, typically operating at a nominal 115 V rms and 50/60 Hz frequency, are fused to ensure protection against potential electrical anomalies.
• Within the board, two isolation transformers effectively execute a three-wire open delta voltage measurement, generating an output of 1.533 V rms from a 115 V rms input. Regarding the CT inputs, two generator current inputs from the CTs are connected to non-pluggable terminal blocks, TB2 and TB3. Each current transformer features a 0-1 A rms winding and a 0-5 A rms winding, with only one wired to EPCT. The cable length from the transformer to the board can extend up to 1000 ft, accommodating wire gauges of up to #10 AWG for reliable transmission.
• Incorporates four voltage test points (TP9-12), strategically positioned on each leg of the secondary side of the generator current isolation transformers. It is crucial to note that these test points should not be grounded through the measuring device.
• This design decision is essential to ensure accurate measurements and prevent potential interference that could compromise the measurement accuracy.
• The board's layout, as depicted in the Board Layout, showcases the arrangement of components. T1 through T6 denote the voltage and current isolation transformers, essential for their respective measurements. Terminal block TB1, held in place by two screws, is designed for removal if necessary. However, terminal blocks TB2 and TB3 are intentionally fixed, serving as a protective measure against a potential CT open circuit situation.
• In a simplex control setup, the voltage signals are directed through the J305 connector to the EMIO board situated in the M1 controller. Conversely, in a redundant control configuration, these signals are distributed, allowing connection to connectors J305, J308, and J315. Subsequently, they are transmitted to controllers M1, M2, and C, ensuring redundancy and system resilience.
• Facilitates measurements through eight voltage test points (TP1-8), strategically located on each leg of the secondary side of the isolation transformers. These test points offer convenient access for diagnostic and testing purposes.
• The system incorporates three 25-pin sub-D connectors, namely J305, J308, and J315. These connectors are designated for cable connections to the EBKP backplane, enabling seamless linkage to the EMIO board, thus facilitating communication and data transfer within the system configuration.

Hot sale series:

General Electric IC693 / IC695 / IC697 / IC698 / IC200 / IC660 / IC670 and other CPU modules, communication modules, analog digital modules.
EX2100, EX2000 Excitation system card IS200 series, DS200 series.

Our advantage brands:
BENTLY EPRO ALL SERIES OF PRODUCTS SPAR PARTS PROBE Proximitor
PLC : AB,ABB,GE,Schneider
DCS : ABB,Siemens MOORE,Foxboro,Westinghouse,YOKOGAWA
ESD : Triconex,HIMA,BENTLY,ICS Triplex
Excitation cards : ABB,GE

Recommended Products:

Products Pictures:

The operating mode of our company is e-commerce, In order to reduce the intermediate links for consumers in the first time to provide quality products and satisfactory service, the company has a sound logistics supply system, is now with many well-known foreign brands manufacturers to establish a good relationship of cooperation.We can directly from the outside of the purchase, to provide different countries, manufacturers of equipment and spare parts to solve your troubles to find more than the quality of the product or worry about the price, we have a great advantage in price, product details, We sincerely welcome you to inquire us use any other method!