Eye-Eye webbing sling is made from high tenacity 100% polyester webbing with reinforced eye loops at both ends.It can be made from one layer to four layers, which we usually call Simplex webbing sling, Duplex webbing sling, Triplex webbing sling and Quadraplex. And the eyes can be made into Flat eyes, Twisted eyes and Reversed eyes. Eye-eye webbing slings are versatile as they can be used in choker, vertical, or basket hitches.Polyester fabric has low elongation, so it’s better able to hold the load without the risk of shocking.OEM service is also available.

1T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S(kg)
	5DEE010	Purple	5:1	25	5T
	6DEE010	Purple	6:1	25/38	6T
	7DEE010	Purple	7:1	30/50/60	7T
	8DEE010	Purple	8:1	50	8T

2T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S(kg)
	5DEE020	Green	5:1	50	10T
	6DEE020	Green	6:1	50	12T
	7DEE020	Green	7:1	50/60	14T
	8DEE020	Green	8:1	65	16T

3T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S
	5DEE030	Yellow	5:1	75	15T
	6DEE030	Yellow	6:1	75	18T
	7DEE030	Yellow	7:1	75/90	21T
	8DEE030	Yellow	8:1	95	24T

4T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S
	5DEE040	Grey	5	100	20T
	6DEE040	Grey	6	100	24T
	7DEE040	Grey	7	100/120	28T
	8DEE040	Grey	8	120	32T

5T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S(kg)
	5DEE050	Red	5:1	125	25T
	6DEE050	Red	6:1	125	30T
	7DEE050	Red	7:1	125/150	35T
	8DEE050	Red	8:1	150	40T

6T WEBBING SLING	Modelo	Color	Safety factor	Widthmm))	M.B.S(kg)
	5DEE060	Brown	5:1	150	30T
	6DEE060	Brown	6:1	150	36T
	7DEE060	Brown	7:1	150/180	42T
	8DEE060	Brown	8:1	180	48T

8T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S
	5DEE080	Blue	5:1	200	40T
	6DEE080	Blue	6:1	200	48T
	7DEE080	Blue	7:1	200/240	56T
	8DEE080	Blue	8:1	240	64T

10T WEBBING SLING	Modelo	Color	Safety factor	Widthmm)	M.B.S
	5DEE100	Orange	5:1	250	50T
	6DEE100	Orange	6:1	250	60T
	7DEE100	Orange	7:1	250/300	70T
	8DEE100	Orange	8:1	300	80T

CAUTIONS:

- Do not attempt to use sling above rated lifting capacity.
- When selecting a sling,it is very important to consider the angles at which the sling will be used.
- Slings are subject to cutting when ifting items with sharp egeds.In this case,always use protective sleeves
- Do not use a damaged sling,and se only if trained.
- Do not tie knots in sling webbing as strength is greatly reduced.
- Never drag a sling beneth from a load which is resting on it.
- Chemical active environments can affect the strength of slings
- Inspect slings weekly or more frequently depending on the sling use conditions.
- Always strore slings in a cool,dry and dark place to extend the working lift.
- Always read and understand the operating instructions before use.
- Failure to comply with this warning may result in serious load damageand death or injury.

When using flat woven webbing slings always:

• Store and handle belt slings correctly.

• Inspect belt slings and accessories before use and before placing into storage.

• Follow safe slinging practices, as given overleaf.

• Position the bight for choke lift at 120° (natural angle).

• Position the sling so that the load is uniformly spread over its width and protect the sling from sharp edges.

• Apply the correct mode factor for the slinging arrangement.

Selecting the Correct Sling

Belt slings are available in a range of materials and sizes in single leg and endless sling forms. Select the slings to

be used and plan the lift taking the following into account:

Material

Polyester is resistant to moderate strength acids but is damaged by alkalis; polyamide (Nylon) is virtually immune to

alkalis but is damaged by acids; and polypropylene is little affected by acids or alkalis but is damaged by some

solvents, tars and paints.

Capacity

The sling must be both long enough and strong enough for the load and the slinging method. Apply the mode factor

for the slinging method. For use at temperatures exceeding 80°C or below 0°C refer to the suppliers instructions. If

the slings are used in multi-leg arrangement the angle formed between the legs should not be less than 30° or

greater than 90°. If abrasion, heat generated by friction or cutting from edges or corners are likely, select a sling

fitted with protective sleeves and/or use suitable packing.

Using Belt Slings Safely

Do not attempt lifting operations unless you understand the use of the equipment, the slinging procedures and the

mode factors to be applied. Do not use defective slings or accessories. Check the correct engagement with fittings

and appliances, ensure smooth radii are formed, do not twist or cross slings and do not overcrowd fittings. Position

the sling so that the load is uniformly spread over its width. Position the bight for a choke lift at the natural (120°)

angle to prevent friction being generated. Ensure that stitching is in the standing part of the sling away from hooks

and other fittings. Take the load steadily and avoid shock loads. Do not leave suspended loads unattended. In an

emergency cordon off the area.

In-service Inspection, Maintenance and Replacement

Inspect slings each day before use, looking for:

• Missing or unreadable ID tag
• Melted, charred or weld-splattered areas
• Acid or alkali burns
• Holes, tears, cuts, snags or embedded particles
• Broken or worn stitching
• Excessive abrasive wear or elongation
• Knots or brittle areas
• Broken, corroded, pitted distorted fittings

Do not use worn or damaged slings or attachments. Discard or repair them. Use damaged slings only after they are repaired, reconditioned, and proof tested by the sling manufacturer or a qualified person. Keep certificates of proof test.