250VAC 50A emi power line filter rf shielding
EMI Filter Mounting Tips
The cables and wiring inside a system including the input power cables can act as an antenna for high-frequency noise (10’s of MHz and up) radiating them through the air as well as picking them. This can pose a serious challenge for mitigating radiated as well as high frequency conducted emissions. The higher frequency (10’s pf MHz and up) noise filtered by the filter circuit can couple back on the other side (cables) via the radiated mode. This makes the installation of the filter quite critical. Keeping the following EMI filter installation recommendations in mind can ensure proper EMI filter performance:
- Mount the filter in a place that requires the shortest cable runs.
- When the aim is noise mitigation, mount the filter as close to the EMI source as possible, whether it's a drive, uninterruptible power source, inverter or another component. The farther it is, the more wiring is available for noise to propagate.
- For EMI compliance, install the filter as close to the point of power entry (POE) as possible.
- Bulkhead mount the filter to the chassis at the point of power entry with proper shielding, creating good input-output isolation.
- If bulkhead mounting is not possible, keep wires/cables at the filter input as short as possible and shield the input cables, if necessary.
- For MIL applications, use the MIL grade connector directly installed on the filter box and bulkhead mount it to the chassis.
- Shield filter output cabling if it’s picking noise from inside the system.
RATED VOLTAGE | 250 VAC |
RATED CURRENT | 30 A |
OPERATIONAL FREQUENCY | 50 60 Hz |
Voltage Drop | Less than 1V |
Overload | 140% of rated current for 15 minutes |
Harmonic Distortion | Less than 2% @ full rated current |
Leakage Current | ≤0.2A@380/230VAC and 50Hz |
Dielectric Withstanding Voltage | 1000VDC (line to line) 1000VDC (line to case) |
DC Insulation Resistance | As Per MIL-STD-202 Method 202 |
Terminal Strength | As Per MIL-STD-202 Method 211 |
Temperature Rise | As Per MIL-F-15733 |
Insertion Loss | ≥100dB@14K-40GHz As Per MIL-STD-220A, Under Load Condition |
Climatic Classification | 25/070/21 |

We Can Supply EMI Filter Like
100a EMI Filter
2 Stage EMI Filter
230v Ac EMI Filter
240v Ac EMI Filter
3 Phase 400hz EMI Filter
3 Phase RFI Filter
50a EMI Filter
AC Socket EMI Filter With Fuse And Switch
EMI Filter 5A
Ac Dc EMI Filter
Ac Input EMI Filter Design
Ac Line Filter For Audio
Ac Power Line Noise Filter
Anti-Interference Filter
Electromagnetic Interference Filters
EMC EMI Filter For PV Inverters
EMI Electrical Power Filter For Equipment
EMI Filter 10a
EMI Filter 230v
EMI Filter Ac
EMI Filter Feedthrough Capacitor
EMI Filter For Led Lights
EMI Filter For Power Supply
EMI Filter For Vfd
EMI Filter Manufacturers
EMI Filters For Mechanical Equipment
EMI RFI Ac Power Line Filters
EMI RFI Noise Filtration
EMI RFI Noise Suppression Protection Filters
Ethernet EMI Filter
Feedthru Capacitors
General Purpose Socket Emc RFI Noise Filter With Fuse
Gigabit Ethernet EMI Filter
Iec EMI Filters
Inline EMI Filter
Inverter EMI Filter
Laser Cutting Single Phase EMI Filter
Lc EMI Filter
Lcr Electronics EMI Filter
Led EMI Filter
Low Pass EMI Filter
Lvds EMI Filter
Mains EMI Filter
Military EMI Filters
Mri Rf Filter
Passive EMI Filter
Plc Noise Filter
Plug In EMI Filters
Power Filter With Fuse For Medical Equipment
Power Line Filters Single Phase
Power Supply EMI Filter
Radio Frequency Interference Filters
RF Feedthrough Capacitor
RFI Filter For Radio
RFI Filter For Tv
RFI Filter For Vfd
RFI Suppression Filter
Rj45 EMI Filter
Single Phase EMI Filter
Single Phase RFI Filter
Solar Inverter EMI Filter
Three Phase EMI Filters
Vfd EMI Filter
EMI Filter With Rocker Switch And Fuse
Two Stages EMI Ac Power RFI Filter ETC.