New Hot Product Advertising LED Screen P8 Outdoor Full Color 1/4 Scan Mode HD

Hardware installation

1. Insert the DVI display card into the AGP slot of the motherboard and install the card driver.

2. Insert the data acquisition card into the empty PCI slot.

3. Connect the data acquisition card and the display card with a DVI cable.

4. Connect the control line to the serial port (Rs232) (optional).

5. Connect to the receiving card with a network cable.

6. Connect the LED display driver card and the hub one by one with a 50P flat cable.

7. Check the settings or power on the debugger.

Specification of product:

Packing and shipping:

In our company,usually use the wooden and flight cases for package,wooden for Iron cabinet,and the flight for Die casting cabinet.In this way can help you to save the transportation expenses.For shipping,we have sea and air,in which way just all up to you.Also,if you want other way,we can accept.

Two types of modules:

A. DIP package

DIP package, which is the abbreviation of dual inline-pin package, commonly known as plug-in type. It was the first to develop. The LED lamp bead is produced by the manufacturer, and then inserted into the LED lamp board of the LED by the LED module and the LED display manufacturer, and the DIP semi-outdoor module and the outdoor waterproof module are produced through wave soldering.

However, due to the influence of the diameter of the lamp bead, only P6 can be achieved at present. Other P5, P4 and even higher density outdoor LED displays cannot be made. However, the protection performance of the direct insertion is good, but the viewing angle is not accurate and fixed, generally between 100-110, and the energy consumption is high, and it is not environmentally friendly, so it is only suitable for outdoor small-pitch LED display, and currently in the outdoor P10-P20 Have a large market share.

Moreover, it is produced by DIP packaging, the process is complicated, it is not easy to mechanize production, and the production efficiency is low. In addition, there are many DIP manufacturers, there is no high technical and equipment threshold, and the competition is fierce. Many manufacturers use inferior raw materials and PCB boards to reduce the cost to gain market share, low quality, and almost no perfect after-sales guarantee.

B. SMD package

SMD package, meaning: surface mount device, which is one of the SMT components. Surface mount components were introduced about twenty years ago and have opened up a new era. For a long time it has been thought that all pin components will eventually be available in SMD packages. SMD technology is widely used in LED outdoor displays.

We often say that the three-in-one label is actually a kind of SMD technology, which means that the SMT lamps of RGB three different color LED chip packages are packaged in the same glue body at a certain interval.

The advantages of the standard three-in-one outdoor full-color LED display are as follows: the full-screen viewing angle is relatively large, and the surface can be treated with light diffuse reflection. The obtained effect is not granular, the color saturation is high, and the color uniformity is good. . The overall flatness of the three-in-one is easier to control and has always been the standard technology used in high-definition outdoor LED displays.

With the continuous improvement of technology development and production technology in recent years, SMD has developed rapidly and cost reduced. It is currently the mainstream product of LED indoor display. Moreover, it has developed rapidly in the outdoor market, but brightness and waterproof and moisture-proof have always been difficult to overcome. I believe that the entire industry continues to develop, the development of outdoor LED display is the direction of the surface.

FAQ

1.Q:Are you a factory or trading company?

A:We are a factory,located in Dalang,Longhua District .

2.Q:What kind of payment terms you accept?

A:We accept T/T,Western Union,MoneyGram etc.

3.Q:What's packaging?

A:1.Flight case packaging

2.Wooden case packaging

3.36pcs in one case packaging

4.Customized packaging

4.Q:Does you have CE/ROHS certificates?

A:Yes, we offer the CE & ROHS certificates .

5.Q:What's the shipping method,shipping time?

A:Our products could be shipped by Sea, by Air, and by Express.

by sea:20-40days; by air:5-10days ;by express:3-6days

Welcome to Shenzhen ShiChuangXin Ke Electronic Co.,Ltd.We are wating for you all the time online!!!