110 KW Energy Efficient Air Compressor SRC-110W 0.8~1.25 Mpa 15.56~20.20 m³/min Schneider Sunshine
1. AM series always maintain over 96% efficiency under any load; Compared with ordinary motor energy saving more than 38%, more than 15% energy saving than induction type frequency conversion motor, than the general induction frequency conversion motor rotor iron loss, armature copper loss and other fixed loss reduced by 30%, the efficiency of course will be higher.
2. Permanent magnet motor:There is a linear relationship between the output torque and the input current, which is most suitable for the application of equipment with constant torque load (note: air compressor is a typical load with constant torque).It is easy to overcome the static friction force when running at a low speed.
⊙ Why the oil free water spray screw technology is needed?
➤ Large capacity
➤ High exhaust pressure (single stage compression pressure up to 17 bar)
➤ High efficiency
➤ Close to isothermal compression
➤ Low noise
➤ Real oil-free stainless-steel screw rotor
➤ Self-lubricating
➤ Oil free ISO85730 level certificate
➤ Lower application costs
➤ Lower maintenance costs
➤ “0” pollution to environment clean and safe compressed air
➤ no fault, long and stable running ability
(1) Stable Pressure
The variable speed air compressor adopts PID for precision speed adjustment. Changes in the air amount of
the system will be automatically tracked. The compressor will supply air at a constant pressure, which is the
preset desired pressure plus or minus 0.1bar, to reduce power consumption.
(2) Variable Flow Control
Adopt inverter to drive the compressor can adjust the rotation speed of the motor in real time according to
the actual air compression. In case of high air consumption, the pressure remains unchanged, but the
speed compensates automatically to meet the supply needs. When the air consumption is low, pressure
is maintained constant and speed is automatically reduced to supply compressed air which is just enough.
(3) No Current Impact during Starting
The air compressor is started via invert. The maximum starting current is 1.2 times the rated current for
power frequency start. Hence, our variable speed air compressor exerts little impact on the grid during
starting. It enjoys reduced stress and consequently prolonged service life.
(4) High Economical Efficiency
Throughout the operating life of the air compressor, energy costs account for most of all costs. However,
by using VSD, energy consumption is reduced by 30%.Therefore, the energy cost saved by a variable
speed air compressor for three years is roughly equivalent to purchase price of the unit.
⊙ Energy Efficient Air Compressor detailed parameters
Model | Maximum working pressure |
FAD | Motor power | Noise | Pipe diameters of cooling water in and out | Quantity of cooling water | Quantity of lubricating water | Dimension | Weight | Air outlet |
Inlet water 32℃ | L×W×H | |||||||||
Mpa | M³/min | KW | DB | T/H | L | mm | KG | |||
SRC-6A/W | 0.8 | 0.78 | 5.5 | 57 | 3/4″ | 1.5 | 10 | 800×800×1100 | 430 | 3/4″ |
1.0 | 0.65 | |||||||||
SRC-8A/W | 0.8 | 1.17 | 7.5 | 57 | 3/4″ | 2 | 10 | 800×800×1100 | 470 | 3/4″ |
1.0 | 1.05 | |||||||||
1.25 | 0.81 | |||||||||
SRC-11A/W | 0.8 | 1.72 | 11 | 60 | 1″ | 2.5 | 26 | 1200×800×1300 | 580 | 3/4″ |
1.0 | 1.42 | |||||||||
1.25 | 1.10 | |||||||||
SRC-15A/W | 0.8 | 2.43 | 15 | 60 | 1″ | 3.5 | 26 | 1200×800×1300 | 620 | 1″ |
1.0 | 2.17 | |||||||||
1.25 | 1.80 | |||||||||
SRC-18A/W | 0.8 | 3.13 | 18.5 | 63 | 1″ | 4 | 30 | 1400×1000×1520 | 680 | 1″ |
1.0 | 2.82 | |||||||||
1.25 | 2.05 | |||||||||
SRC-22A/W | 0.8 | 3.7 | 22 | 63 | 1″ | 5 | 30 | 1400×1000×1520 | 730 | 1″ |
1.0 | 3.21 | |||||||||
1.25 | 2.78 | |||||||||
SRC-30A/W | 0.8 | 5.2 | 30 | 66 | 1 ½″ | 7 | 40 | 1500×1150×1500 | 1100 | 1 ½″ |
1.0 | 4.43 | |||||||||
1.25 | 3.36 | |||||||||
SRC-37A/W | 0.8 | 6.50 | 37 | 66 | 1 ½″ | 9 | 40 | 1500×1150×1500 | 1150 | 1 ½″ |
1.0 | 5.33 | |||||||||
1.25 | 4.77 | |||||||||
SRC-45W | 0.8 | 8.30 | 45 | 68 | 1 ½″ | 10 | 90 | 1800×1300×1750 | 1390 | 2″ |
1.0 | 6.30 | |||||||||
1.25 | 5.56 | |||||||||
SRC-55W | 0.8 | 10.3 | 55 | 69 | 1 ½″ | 12 | 100 | 1800×1300×1750 | 1470 | 2″ |
1.0 | 8.55 | |||||||||
1.25 | 7.67 | |||||||||
SRC-65W | 0.8 | 11 | 65 | 70 | 1½″ | 15 | 100 | 1800×1300×1750 | 1430 | 2″ |
SRC-75W | 0.8 | 13.00 | 75 | 72 | 1½″ | 18 | 100 | 1800×1300×1750 | 1630 | 2″ |
1.0 | 11.50 | |||||||||
1.25 | 9.70 | |||||||||
SRC-90W | 0.8 | 16.60 | 90 | 73 | 1½″ | 20 | 120 | 2200×1550×1800 | 2350 | 2½″ |
1.0 | 14.66 | |||||||||
1.25 | 12.60 | |||||||||
SRC-110W | 0.8 | 20.20 | 110 | 77 | 2″ | 24 | 120 | 2200×1550×1800 | 2460 | 2½″ |
1.0 | 16.66 | |||||||||
1.25 | 15.56 | |||||||||
SRC-132W | 0.8 | 22.52 | 110 | 77 | 2″ | 24 | 120 | 2200×1550×1800 | 2460 | 2½″ |
1.0 | 16.66 | |||||||||
1.25 | 15.56 | |||||||||
SRC-160W | 0.8 | 28.11 | 160 | 79 | 3″ | 35 | 160 | 3000×1800×2100 | 3700 | 3″ |
1.0 | 25.45 | |||||||||
1.25 | 22.52 | |||||||||
SRC-185W | 0.8 | 33.97 | 185 | 79 | 3″ | 38 | 160 | 3000×1800×2100 | 3750 | 3″ |
1.0 | 29.00 | |||||||||
1.25 | 25.21 | |||||||||
SRC-200W | 0.8 | 36.75 | 200 | 80 | 4″ | 42 | 200 | 3100×1850×2100 | 3900 | 4″ |
1.0 | 32.78 | |||||||||
1.25 | 29.24 | |||||||||
SRC-220W | 0.8 | 39.67 | 220 | 80 | 4″ | 47 | 200 | 3100×1850×2100 | 4200 | 4″ |
1.0 | 36.75 | |||||||||
1.25 | 29.63 | |||||||||
SRC-250W | 0.8 | 45 | 250 | 80 | 4″ | 53 | 200 | 3100×1850×2100 | 4600 | 4″ |
1.0 | 39.67 | |||||||||
1.25 | 33.97 |
Q. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We'll show you the photos of the products and packages
and then you pay balance. Other payment terms can also be negotiated.
Q. How about your delivery time?
A: For common working volatage and normal color, it will take 7-10 working days after receiving your payment.
Other working volatage and colors will take more time about 10-20 working days
Q. Can you produce according to the samples?
A: Yes, we can produce mold by your samples or technical drawings.
Q. Do you test all your machines before delivery?
A: Yes, we have 100% test before delivery.
Q. Do you have some videos where we can see the line producing?
A: Yes, we can provide some videos for reference.