1746-NO8V AB 16-bit 320 µV/count SLC 500 analog output module

Technical Specifications for 1746-NO8V
Manufacturer Rockwell Automation
Optional Output Data Parameters User defined scale limits Output clamping limit Output alarm limits Ramp rate/limit Preset fault value Output behavior under fault condition (reset, hold, preset) Alarms latch Reset latched alarms
SLC Data Formats Scaled engineering units Scaled for PID Proportional counts 1746-NO4 format User-defined scale
Backplane Power consumption 5.6W
Backplane current consumption 120 mA at 5V dc 160 mA at 24V dc (J4 jumper set to RACK) 0 mA at 24V dc (J4 jumper set to EXT)
Compatible chassis Any 1746 chassis slot except slot 0
Output coding -32,768 to +32,767
Output voltages -10 to +10VDC; -10.25 to +10.25VDC; 0 to 10VDC; 0 to 5VDC and 1 to 5VDC.
Output wiring Single-ended
Brand AB
Part Number/Catalog No. 1746-NO8V
Series SLC 500
Module Type Analog output module
Resolution 16-bit 320 µV/count
Outputs 8
Backplane Current (5 Volts) 120 milliamps
Backplane Current (24 Volts) 160 milliamps
Update Time 540 microseconds/8 channel
Step Response 1 millisecond
Step Response 60 milliseconds in, 2.5 milliseconds out
UPC 10781180054560
UPC 10781180054577

OTHER SUPERIOR PRODUCTS

EtherNet/IP Network Configuration
EtherNet/IP Communication Modules
1756-ENBT, 1756-EN2F, 1756-EN2T, 1756-EN2TP, 1756-EN2TPK, 1756-EN2TPXT, 1756-EN2TR, 1756-EN2TRXT,
1756-EN2TSC, 1756-EN2TXT, 1756-EN3TR, 1756-EWEB, 1768-ENBT
CompactLogix 5370 Controllers
EtherNet/IP Adapters
1734-AENT, 1734-AENTR, 1769-AENTR, 1794-AENT, 20-COMM-E, 22-COMM-E, 20-750-ENETR
Embedded Switches
1783-ETAP, 1783-ETAP1F, 1783-ETAP2

The AB 1746-C7 cable is a ribbon power cable that connects controllers and chassis. The spacing between the controllers and chassis are important to note. When using the 1746-C7 cable to connect SLC 500 controllers, the space between them should be between 2.5 and 4 inches. When using the cable to connect AB 1746-P4 power supplies, the maximum spacing between the supplies is 2.5 inches. The 1746-C7 cable itself measures 6 inches in length. It should only be used to connect chassis and controllers side by side, not in a stacked formation with one chassis or controller above the other.

The 1746-C7 cable is best-suited for connecting AB 1746-A4, 1746-A7, 1746-10, and 1746-A13 chassis. The cable can connect these chassis in any combination with each other (for example, the 1746-C7 cable can connect 2 1746-A4 chassis to each other, it can connect 1 1746-A4 chassis to any of the other chassis listed).

FAQ for 1756-PB75
What is the difference between the 1756-PA75 and 1756-PB75?

The 1756-PA75 operates when supplied with 85-264VAC while the 1756-PB75 is powered by an external 18-32VDC supply voltage.

Can I use this power supply as voltage source of panel components?

No. This power supply is intended only for the ControlLogix chassis.

What are compatible ControlLogix chassis for use with the 1756-PB75?

Compatible chassis are 1756-A4, 1756-A7, 1756-A10, 1756-A13, 1756-A17.