General Electric DS3800HFXD1F1E Signal Conditioning Board GE Mark IV

Product Description
DS3800HFXD1F1E Signal Conditioning Board GE Mark IV

The DS3800HFXD1F1E is a Signal Conditioning Board manufactured by General Electric for use within the Mark IV Speedtronic system.

The DS3800HFXD1F1E is a rectangular board that is heavily populated with components. The left edge of the board is taken up by a backplane connector marked 218A4553-1 AMP 533002-1. The right side of the board also has a right-angled connector component, marked M8350324-19. The board has one additional connector located in the center of the board; this is a vertical pin male connector.

The DS3800HFXD1F1E is marked on its top edge for alignment purposes. Corners are drilled, with extractor clips added to the two right corners. These clips are used to simplify both extraction and insertion processes, as the clips can be used to push/pull the board from its place within a rack and can also be used as a handle during insertion.

The DS3800HFXD1F1E has four nylon standoffs mounted to its surface on the right board side. These allow for the addition of an auxiliary board. There are eight jumper switches, three LED indicators (one amber, two red,) one toggle switch, four TP test points, and four resistor network arrays. The board uses metal film resistor network arrays, ceramic and electrolytic capacitors, and diode components. It is populated by over fifty integrated circuits, including 8-bit Tri-State Bidirectional Transceivers, Octal Buffers/Line Drivers/Line Receivers, and Hex/Quad D Flip-Flops.

For additional information, please consult technical support publications like manuals or datasheets originally provided by GE.

OTHER SUPERIOR PRODUCTS

Similar prodcut for GE

DS3800DDCD181A
DS3800DDCD18IA
DS3800DDCD18LA
DS3800DDCD1BIA
DS3800DDCD1BLA
DS3800DDCDI81A
DS3800DDCDI8IA
DS3800DDCDI8LA
DS3800DDCDIB1A
DS3800DDCDIBIA
DS3800DDCDIBLA
DS3800DDCDL81A
DS3800DDCDL8IA
DS3800DDCDL8LA
DS3800DDCDLB1A
DS3800DDCDLBIA
DS3800DDCDLBLA
DS380ODDCD181A
DS380ODDCD18IA
DS380ODDCD18LA
DS380ODDCD1B1A
DS380ODDCD1BIA
DS380ODDCD1BLA
DS380ODDCDIB1A
DS380ODDCDIBIA
DS380ODDCDIBLA
DS3800DDCD1B1A-A
DS3800DDCD1B1A-B
DS3800DDCD1B1A-C
DS3800DDCD1B1A-D
DS3800DDCD1B1A-E
DS3800DDCD1B1A-F
DS3800DDCD1B1A-G
DS3800DDCD1B1A-H
DS3800DDCD1B1A-I
DS3800DDCD1B1A-J
DS3800DDCD1B1A-K
DS3800DDCD1B1A-L
DS3800DDCD1B1A-M
DS3800DDCD1B1A-N
DS3800DDCD1B1A-O
DS3800DDCD1B1A-P
DS3800DDCD1B1A-Q
DS3800DDCD1B1A-R
DS3800DDCD1B1A-S
DS3800DDCD1B1A-T
DS3800DDCD1B1A-U
DS3800DDCD1B1A-V
DS3800DDCD1B1A-W
DS3800DDCD1B1A-X
DS3800DDCD1B1A-Y
DS3800DDCD1B1A-Z

Product Description

The DS3800DBIB is a small printed circuit board (PCB) designed as part of the Speedtronic (Mark IV) line manufactured by GE. The Speedtronic system is designed to sequence turbine fuel and to sequence turbine systems and their auxiliaries for startup. The Mark IV system is designed with a distributed control system which runs on an array of interconnected microprocessors. When one section of this gridwork fails, turbines will continue to work under the control of other parts of the system. In this way downtime is limited. The DS3800DBIB is designed specifically as an interface board.

The DS3800DBIB is a small daughterboard that works as a plug-in to another, larger PCB. It has been drilled out at the factory, one hole in each corner of the board. This board also has four connectors numbered 1 through 4. It has two small screw mounts covered by black tabs. The first mount is marked C101 and is positioned next to a ring marked TP1. The second is not marked and positioned next to a ring marked TP2. The DS3800DBIB has one capacitor rated 708A1, M/E 200V 1.0 +10%. It also has one blue potentiometer located on the edge of the board that is wired for variable resistance. There are ten resistors and six small capacitors marked 'cr' on the DS3800DBIB PCB

Q1. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.

Q2. Do you have any MOQ limit of Industrial Servo Drives?
A: Low MOQ, 1pc is available.

Q3. How do you ship the goods and how long does it take to arrive?
A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.

Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.