GE Universal Communications Processor Board DS3800HCMB for quick installation in the drive

Product Description
The GE Universal Communications Processor Board DS3800HCMB is designed for quick installation in the drive. The board features a modular connector on 1 end and retention levers on the other end. The GE Universal Communications Processor Board DS3800HCMB also is populated with a microprocessor and 1 40-pin connector on the surface of the board. The board is populated with 1 amber indicator LED and standoffs. The board is also populated with 3 sockets for electrically erasable programmable read-only memory (EEPROM) modules and 25 jumpers.

The standoffs on the GE Universal Communications Processor Board DS3800HCMB are plastic and do not require use of screws to install a daughter card. Instead, the installer or technician presses the daughter card over the standoff to secure it. To remove a daughter card, the installer lifts 1 corner at a time from the standoff. The standoffs keeps the daughter card from touching the surface of the board and interfering with the components and processing functions. The daughter card is an optional device that is designed for use with the board. It is not a stand-alone device but instead works with the board. It provides features not available on the board and it also provides additional memory, processing, and other optional functionality.

While the standoffs provide a means to physically connect the daughter card and the GE Universal Communications Processor Board DS3800HCMB, the 40-pin ribbon cable carries the electrical and controls signals used by the daughter card. The 40-pin ribbon cable is approximately 7-inches in length and it connects to the 40-pin connector on the board.

OTHER SUPERIOR PRODUCTS

Similar prodcut for GE

DS3800DDCD181A
DS3800DDCD18IA
DS3800DDCD18LA
DS3800DDCD1BIA
DS3800DDCD1BLA
DS3800DDCDI81A
DS3800DDCDI8IA
DS3800DDCDI8LA
DS3800DDCDIB1A
DS3800DDCDIBIA
DS3800DDCDIBLA
DS3800DDCDL81A
DS3800DDCDL8IA
DS3800DDCDL8LA
DS3800DDCDLB1A
DS3800DDCDLBIA
DS3800DDCDLBLA
DS380ODDCD181A
DS380ODDCD18IA
DS380ODDCD18LA
DS380ODDCD1B1A
DS380ODDCD1BIA
DS380ODDCD1BLA
DS380ODDCDIB1A
DS380ODDCDIBIA
DS380ODDCDIBLA
DS3800DDCD1B1A-A
DS3800DDCD1B1A-B
DS3800DDCD1B1A-C
DS3800DDCD1B1A-D
DS3800DDCD1B1A-E
DS3800DDCD1B1A-F
DS3800DDCD1B1A-G
DS3800DDCD1B1A-H
DS3800DDCD1B1A-I
DS3800DDCD1B1A-J
DS3800DDCD1B1A-K
DS3800DDCD1B1A-L
DS3800DDCD1B1A-M
DS3800DDCD1B1A-N
DS3800DDCD1B1A-O
DS3800DDCD1B1A-P
DS3800DDCD1B1A-Q
DS3800DDCD1B1A-R
DS3800DDCD1B1A-S
DS3800DDCD1B1A-T
DS3800DDCD1B1A-U
DS3800DDCD1B1A-V
DS3800DDCD1B1A-W
DS3800DDCD1B1A-X
DS3800DDCD1B1A-Y
DS3800DDCD1B1A-Z

Product Description

The DS3800DBIB is a small printed circuit board (PCB) designed as part of the Speedtronic (Mark IV) line manufactured by GE. The Speedtronic system is designed to sequence turbine fuel and to sequence turbine systems and their auxiliaries for startup. The Mark IV system is designed with a distributed control system which runs on an array of interconnected microprocessors. When one section of this gridwork fails, turbines will continue to work under the control of other parts of the system. In this way downtime is limited. The DS3800DBIB is designed specifically as an interface board.

The DS3800DBIB is a small daughterboard that works as a plug-in to another, larger PCB. It has been drilled out at the factory, one hole in each corner of the board. This board also has four connectors numbered 1 through 4. It has two small screw mounts covered by black tabs. The first mount is marked C101 and is positioned next to a ring marked TP1. The second is not marked and positioned next to a ring marked TP2. The DS3800DBIB has one capacitor rated 708A1, M/E 200V 1.0 +10%. It also has one blue potentiometer located on the edge of the board that is wired for variable resistance. There are ten resistors and six small capacitors marked 'cr' on the DS3800DBIB PCB

Q1. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.

Q2. Do you have any MOQ limit of Industrial Servo Drives?
A: Low MOQ, 1pc is available.

Q3. How do you ship the goods and how long does it take to arrive?
A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.

Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.