HP Compatible SMF 10G SFP+ Optical Transceiver 1310nm 10km DOM LC
HP Compatible 10GBase-LR SFP+ Transceiver (SMF, 1310nm, 10km, DOM, LC)
● 10 Gigabit Fiber SFP+ Transceiver
● SMF LC with DOM
● 10km distance
● 1310 nm optical wavelength
● < 1W Power Dissipation
● Operating case temperature: Commerical:0~70°C, Industrial:-40 to 85 °C
Electrical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 85 ℃,VCC = 3.13 to 3.47 V)
Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
Transmitter | ||||||
Differential data input swing | VINPP | 180 | 700 | mVpp | 1 | |
Transmit Disable Voltage | VD | VCC-0.8 | Vcc | V | ||
Transmit Enable Voltage | VEN | Vee | Vee+0.8 | |||
Input differential impedance | Rin | 100 | Ω | |||
Receiver | ||||||
Differential data output swing | Vout,pp | 300 | 850 | mVpp | 2 | |
Output rise time and fall time | Tr, Tf | 28 | Ps | 3 | ||
LOS asserted | VLOS_F | VCC-0.8 | Vcc | V | 4 | |
LOS de-asserted | VLOS_N | Vee | Vee+0.8 | V | 4 |
Note:
1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
2. Into 100Ω differential termination.
3. 20 – 80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’s and four 0’s sequence in the PRBS 9 is an acceptable alternative.
4. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal operation is logic 0; loss of signal is logic 1.
Optical Characteristics (TOP(C) = 0 to 70 ℃, TOP(I) =-40 to 85 ℃,VCC = 3.13 to 3.47 V)
Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
Transmitter | ||||||
Operating Wavelength | λ | 1260 | 1310 | 1355 | nm | |
Ave. output power (Enabled) | PAVE | -6 | 0 | dBm | 1 | |
Side-Mode Suppression Ratio | SMSR | 30 | dB | |||
Extinction Ratio | ER | 4 | 4.5 | dB | ||
RMS spectral width | Δλ | 1 | nm | |||
Rise/Fall time (20%~80%) | Tr/Tf | 50 | ps | |||
Dispersion penalty | TDP | 3.2 | dB | |||
Relative Intensity Noise | RIN | -128 | dB/Hz | |||
Output Optical Eye | Compliant with IEEE 0802.3ae | |||||
Receiver | ||||||
Operating Wavelength | 1270 | 1600 | nm | |||
Receiver Sensitivity | PSEN2 | -14.4 | dBm | 2 | ||
Overload | PAVE | 0.5 | dBm | |||
LOS Assert | Pa | -30 | dBm | |||
LOS De-assert | Pd | -18 | dBm | |||
LOS Hysteresis | Pd-Pa | 0.5 | dB |
Notes:
1. Average power figures are informative only, per IEEE 802.3ae.
2. Measured at the BER less than 1E-12, back to back. The measure pattern is PRBS 231-1 with worst ER=4.5@ 10.3125Gb/s.
Product Descriptions
Olinkcom’s OLSP311XL-CD10 delivers 10 Gigabit connectivity over singlemode fiber cable with a range of up to 10km.
It provides a dependable and cost-effective way to add, replace or upgrade the ports on your networking equipment.
Applications
● 10G Base-SR/SW at 10.3125G
● 10G Fiber Channel
● Other optical links
● 10G Ethernet
The HP compatible 10G SFP+ LC SR transceiver works with the following HP 10G Ethernet Switches and Routers.
• HP A5120 EI Switch Series
• HP A5500 EI Switch Series
• HP A5500 SI Switch Series
• HP A5800 Switch Series
• HP A5810 Switch Series
• HP A5820 Switch Series
• HP E4210G Switch Series
• HP E4500G Switch Series
• HP E4510G Switch Series
• HP E4800G Switch Series
• HPE FlexNetwork 7500 Switch Series
• HPE FlexFabric 7900 Switch Series
• HPE FlexFabric 11900 Switch Series
• HPE FlexNetwork 10500 Switch Series