EPS panel: Volume density16~20kg/m3, Side no straightness ≤1mm/m, radian≤3mm/m.

Width Socket panel 1150±1mm

H panel Roof Panel 1200±1mm

Length unit should greater than 5m, board face should be smooth, denivellation should less than 1.5mm/m

4. Thickness AS Shown IN The Table Below

Should use self-extinguishing flame retardant type, oxygen index greater than 30.

EPS board rest of the standard should be consistent with the CB10801 prescribed standards

The PU adhesive strength should be greater than 10 n/cm2

Group A: appearance of yellow sticky homogeneous liquid. Viscosity ND0.4 ~ 0.7 Pa. S

Group B: look brown sticky homogeneous liquid. Viscosity ND0.3 ~ 0.6 Pa. S

A,B group matching ratio should be 1:1. 5. Glue should be without impurities

At room temperature and foaming time should be at 20 ~ 40 seconds, curing time should be in 50 ~ 70 seconds.

1. Core material rick for free

1.1. Blanking plate frame: place blanking plate coiled material, each side one, and each can be placed a roll of blanking plate

1.2 Down steel plate frame

1.3 There are two sets of drops of glue, and Make the uniform, to adapt different type plate

1.4 Equipped with a pressure blanking plate into "[" type blanking plate, with power plant

A. With the host compound speed synchronous mechanism

B. Several sets of forming rollers, To adapt to the produce of 50, 75, 100, three kinds of thickness of the plate

C.On both sides of the "[" type sealing plate spacing in 1103 mm can be fine-tuning

D. Equipped with two frequency converters to setup control movement speed

1.5.Equipped with steel plate cutting device to cut steel plate

1.6. Equipped with two sets of port plate CAM profiling

1.7. A pressure to strengthen institutions, can raise no pressure or down pressure to strengthen

1.8. One floodlight

2.Main Motor

2.1. Numbers of rubber roller compaction sandwich plate movement

2.2 One set glue and homogenize device

2.3. A set of glue pump components

2.4. A set of pressure to reinforcing rib

2.5. Cutter for cut the upper steel plate

2.6. One electric control box, two inverters, control host speed and the quantity of adhesive glue pump respectively.

2.7. 4 sets of Jack plate forming device, Can be individual adjust the feeding depth by manual and mechanical.

2.8. 4 sets of groover.

2.9. All kinds of beader

3.Two Floodlights

3.1. One escalator

3.2 coreboard cutter

3.3. One electric control cabinet

3.4.One builtin frequency converter for control cutting knife speed. One built-in variable process controller, control cutting knife automatic variable motion.

3.5. Pressure cylinder and reset the cylinder

3.6. One pedestal

A .Main transmission rack

B. assistant transmission rack

Down steel plate frame

Main motor

Cutting machine and the pedestal

Transmission rack1

Transmission rack2

Plate holder

Lifting Hook

1 set

1 set

1 set

1 set

1 set

4 pcs

1 pc

Color plate leader clips

Brake gear

Edge sealing device

Edge sealing steel strip holder

Touch screen

Corrugated roll forming machine

Block machine(optional)

Color steel slitter(optional)

2 pcs

3 set

2 set

1 pc

1 set

1 set

1 set

1 set

Holder

Slitter

Various kinds special spanner

Infrared heating tube

Dust collection fan

Reinforced plastic pipe, sponge, air cushion plastic

Corrugated pipe

Glue dripping pipe

Anchor bolt

1 pc

1 set

1 set

6 pcs

1 set

some

1set

1 set

16 pcs

Spacer

Strainer device

Tracheal clip, folder

Throat

Sealing Gum

16 pcs

2 set

20 pcs

10 pcs

1pc

1.Manufacturing shop should be able to put the production line, the raw materials and corresponding operation space

2.Workshop should be configured one above 5 t crane (Single-girder crane also can be configured to meet the requirements), the crane hook height is greater than 3.8 m from the ground.

3.Configurationof above 0.3 m3/7 kg air compressor and moderate pipelines

4. Workshop environment temperature should be greater than 5 ℃

5.Workshop floor should level off, flatness≤ 5 mm / 10 m, according to the ground plot (the appended drawings)

6. According to the ground plot configured auxiliary power supply, power supply and workshop lighting, etc

7. Prepare debug equipment

8.Color steel: 2 coils, each coil is not less than 3 t, not more than 5 t

9.Glue: conform to the current environment temperature of A, B glue each one barrel, total of 0.45 t

10. Core material: moderate EPS plate of various specifications