47.1 Inch Bar Type Tft Lcd 3840x160 Ips Viewing Angle Lvds Interface 51 Pins
General Description:
DV471FBM-N10 backlighting side entry WLED light source, the light source life is 50K hours, including LED driver. V-by-One 8 lane signal interface, a total of 51 pins, using the terminal connection, drive screen voltage is 12.0V (Typ.), it is a typical vertical refresh rate Fv 60Hz.
Specifications:
Parameter | Specification | Unit | Remarks |
Active area | 1196. 16(H) × 49.84 (V) | mm | |
Number of pixels | 3840(H) × 160(V) | pixels | 1Pixel=(R+G+B) Dot |
Pixel pitch | 311.5(H) × 311.5(V) | um | R/G:103.83, B:103.84 |
Pixel arrangement | Pixels RGB Vertical stripe | ||
Display colors | 16.7M | colors | 8bits True |
Display mode | Normally Black | ||
Dimensional outline | 1209(H)*62.9(V)*14.5(B) | mm | |
Weight | TBD | g | |
Power Consumption | 17W | Watt | Estimate: 6.5W for P anel, 10.5W for BLU |
Bezel width (L/R/U/D) | 5.4/5.4/5.2/6.8 | mm | |
Surface Treatment | Haze 25% | ||
Back-light | Horizontal arranged, 2-LED Lighting Bar type |
Absolute Maximum Ratings:
Parameter | Symbol | Min. | Max. | Unit | Remark |
Power Supply Voltage |
VDD | VSS-0.3 | 13.2 | V |
Ta = 25 ℃ |
VBL | VSS-0.3 | 13.2 | V | ||
Operating Temperature | TOP | 0 | +50 | ℃ |
|
Storage Temperature |
TSUR |
-20 | +60 | ℃ | |
TST |
-20 | +60 | ℃ | ||
Operating Ambient Humidity | Hop | 10 | 80 | %RH | |
Storage Humidity | Hst | 10 | 80 | %RH |
Electrical Specifications:
Parameter | Symbol | Values | Unit | |||
Min | Typ | Max | ||||
Power Supply Input Voltage | VDD | 10.8 | 12 | 13.2 | Vdc | |
Power Supply Ripple Voltage | VRP | 300 | mV | |||
Power Supply Current | IDD | - | 542 | 1000 | mA | |
Power Consumption | PDD | 6.5 | 13.2 | Watt | ||
Rush current |
IRUSH |
- |
10 |
A |
||
V-by-One Interface |
Differential Input High Threshold Voltage | VLVTH |
- |
- |
+50 | mV |
Differential Input Low Threshold Voltage |
VLVTL | -50 |
- |
- |
mV | |
CMOS Interface |
Input High Threshold Voltage |
VIH | 2.0 |
- |
3.3 | |
Input Low Threshold Voltage |
VIL | 0 |
- |
0.8 | V |
Interface Connection:
Pin No | Description | Pin No | Description |
1 | VDD _12V | 16 | NC, For BOE Internal use |
2 | VDD _12V | 17 | NC, For BOE Internal use |
3 | VDD _12V | 18 | NC, For BOE Internal use |
4 | VDD _12V | 19 | NC, For BOE Internal use |
5 | VDD _12V | 20 | NC |
6 | VDD _12V | 21 | NC |
7 | VDD _12V | 22 | SEL-Section |
8 | VDD _12V | 23 | NC |
9 | NC | 24 | GND |
10 | GND | 25 | HTPDN |
11 | GND | 26 | LOCKN |
12 | GND | 27 | GND |
13 | GND | 28 | Rx0n |
14 | NC, For BOE Internal use | 29 | Rx0p |
15 | NC, For BOE Internal use | 30 | GND |
31 | Rx1n | 42 | GND |
32 | Rx1p | 43 | Rx5n |
33 | GND | 44 | Rx5p |
34 | Rx2n | 45 | GND |
35 | Rx2p | 46 | Rx6n |
36 | GND | 47 | Rx6p |
37 | Rx3n | 48 | GND |
38 | Rx3p | 49 | Rx7n |
39 | GND | 50 | Rx7p |
40 | Rx4n | 51 | GND |
41 | Rx4p |
Optical Specification:
Parameter | Symbol | Condition | Min | Typ | Max | Unit | ||
Viewing Angle |
Horizontal |
Θ3 |
CR > 10 |
85 | 89 | - | Deg. | |
Θ9 | 85 | 89 | - | Deg. | ||||
Vertical |
Θ12 | 85 | 89 | - | Deg. | |||
Θ6 | 85 | 89 | - | Deg. | ||||
Brightness | Lv |
Θ=0° (Center) Normal Viewing Angle |
400 | 500 | - | nit | ||
Contrast ratio | CR | 700:1 | 1000:1 | - | ||||
White Iuminance uniformity | ΔY | 75 |
- |
- |
% | |||
Reproduction of color |
White |
Wx |
-0.03 |
0.313 |
+0.03 |
|||
Wy |
0.329 | |||||||
Red |
Rx |
TBD | ||||||
Ry |
TBD | |||||||
Green |
Gx |
TBD | ||||||
Gy |
TBD | |||||||
Blue |
Bx |
TBD | ||||||
By |
TBD | |||||||
Color Gamut | 70 | 72 | % | |||||
Response Time | G to G | Tg | ms |
Handling Precautions:
1.Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference.
2.Design the length of cable to connect between the connector for back-light and the converter as shorter as possible and the shorter cable shall be connected directly , The long cable between back-light and Converter may cause the Luminance of LED to lower and need a higher startup voltage