15.6 Inch Lcd Display 1366x768 With Edp Interface 30 Pins NT156WHM-N12
General Description:
NT156WHM-N12 is a 15.6-inch LCD module product with a-Si TFT-LCD technology, it is assembled with WLED backlight, including LED driver backlight driver, no touch.
Specifications:
Parameter | Specification | Unit |
Active area | 344.23(H) × 193.54(V) | mm |
Number of pixels | 1366 (H) × 768 (V) | pixels |
Pixel pitch | 0.252 (H) X 0.252 (V) | mm |
Pixel arrangement | RGB Vertical stripe | |
Display colors | 262K | colors |
Display mode | Normally White | |
Dimensional outline | 359.5(H)*223.8(V) (W/PCB)*3.8(Max) | mm |
Weight | 400 (max) | g |
Surface treatment | Glare | |
Back-light | Lower Down side, 1-LED Lighting Bar type | |
| PD : 1.2 (max) | W |
PBL :2.6(max) | W | |
Ptotal :3.8(max) | W |
Absolute Maximum Ratings:
Parameter | Symbol | Min. | Max. | Unit |
Power Supply Voltage | VDD | -0.3 | 4.0 | V |
Logic Supply Voltage | VIN | Vss-0.3 | VDD+0.3 | V |
Operating Temperature | TOP | 0 | +50 | ℃ |
Storage Temperature | TST | -20 | +60 | ℃ |
Electrical Specifications:
Parameter | Min. | Typ. | Max. | Unit | |
Power Supply Voltage | VDD | 3.0 | 3.3 | 3.6 | V |
Permissible Input Ripple Voltage | VRF | - | - | 100 | mV |
Power Supply Current | IDD | - | TBD | - | mA |
Differential Input Voltage | VID | 200 | - | 600 | mV |
| PD | - | 1.02 | 1.2 | W |
PBL | - | - | 2.6 | W | |
Ptotal | - | - | 3.8 | W |
Interface Connection:
Terminal | Symbol | Functions |
Pin No. | Symbol | Description |
1 | CABC_ENABLE | Reserved DCR function, not open for now |
2 | H_GND | Ground |
3 | NC | No Connection |
4 | NC | No Connection |
5 | H_GND | Ground |
6 | LANE0_N | eDP RX channel 0 negative |
7 | LANE0_P | eDP RX channel 0 positive |
8 | H_GND | Ground |
9 | AUX_CH_P | eDP AUX CH positive |
10 | AUX_CH_N | eDP AUX CH negative |
11 | H_GND | Ground |
12 | LCD_VCC | Power Supply, 3.3V (typ.) |
13 | LCD_VCC | Power Supply, 3.3V (typ.) |
14 | LCD_Self_Test | Panel self test enable |
15 | H_GND | Ground |
16 | H_GND | Ground |
17 | HPD | Hot plug detect output |
18 | BL_GND | LED Ground |
19 | BL_GND | LED Ground |
20 | BL_GND | LED Ground |
21 | BL_GND | LED Ground |
22 | BL_ENABLE | LED enable pin(+3.3V Input) |
23 | BL_PWM | System PWM Signal Input |
24 | NC | No Connection |
25 | COLOR_ENABLE | test enable |
26 | BL_POWER | LED Power Supply 5V-21V |
27 | BL_POWER | LED Power Supply 5V-21V |
28 | BL_POWER | LED Power Supply 5V-21V |
29 | BL_POWER | LED Power Supply 5V-21V |
30 | NC | No Connection |
Handling Precautions:
1.When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged.
2.Put the module display side down on a flat horizontal plane.