11.6 Inch 1920x1080 Lcd Panel All Viewing Angle 30 Pin Edp 220 Nit
General Description:
The manufacturer of M116B30-040-121-0102 is BOE, led lifetime is 30k hours, viewing angle is 89/89/89/89, Contrast Ratio is 1000, Response Time is 25ms, NTSC ratio is 72%, Luminance of white is 220nit, White uniformity 13pt is 1.3
Specifications:
Parameter | Specification | Unit | Note |
Display size | 11.6” (Diagonal) | inch | |
Active area | 256.32(H) ×144 . 18(V) | mm | |
Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel | |
Pixel pitch | 0.1335(H) x 0.1335 (V) | mm | |
Pixel configuration | R, G, B vertical stripe | ||
Display mode | Normally black | ||
Surface treatment of front polarizer |
Anti-glare coating: (3H) |
Interface Connection:
CN1 (eDP signals , +3.3V DC power supply and B/L power supply)
Pin No. | Symbol | I/O | Function | Remark |
1 | CABC_EN / NC | - | Reserved for CD | [Note1] |
2 | H_GND | P | High Speed round | [Note2] |
3 | Lane1_N | I | Complement Signal Link Lane 1 | |
4 | Lane1_P | I | True Signal Link Lane 1 | |
5 | H_GND | P | High Speed round | [Note2] |
6 | Lane0_N | I | Complement Signal Link Lane 0 | |
7 | Lane0_P | I | True Signal Link Lane 0 | |
8 | H_GND | P | High Speed round | [Note2] |
9 | AUX_CH_P | I | True Signal Auxiliary Channel | |
10 | AUX_CH_N | I | Complement Signal Auxiliary Channel | |
11 | H_GND | P | High Speed round | [Note2] |
12 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
13 | LCD_VDD | P | LCD logic and driver power(3.3V) | |
14 | NC | I | Reserved for LCD manufacturer’s use | [Note1] |
15 | LCD_GND | P | LCD logic and driver ground | |
16 | LCD_GND | P | LCD logic and driver ground | |
17 | HPD | O | HPD signal pin | |
18 | LED-1 | P | Backlight ground | |
19 | LED-2 | P | Backlight ground | |
20 | LED-3 | P | Backlight ground | |
21 | LED-4 | P | Backlight ground | |
22 | BL_ENABLE | I | Backlight on/off | |
23 | BL_PWM_DIM | I | System PWM | |
24 | SCL/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
25 | SDA/NC | - | Reserved for LCD manufacturer’s use | [Note1] |
26 | BL_PWR | P | Backlight power | |
27 | BL_PWR | P | Backlight power | |
28 | BL_PWR | P | Backlight power | |
29 | BL_PWR | P | Backlight power | |
30 | NC | - | Reserved for LCD manufacturer’s use | [Note1] |
[Note]:P: POWER I: Input O: Output
[Note1] Don’t input any signals or any powers into a NC pin. Keep the NC pin open.
[Note2] The shielding case is connected with signal GND.Connector used :20455-030E-76(I-PEX),Corresponding connector : 20453-030T (I-PEX)
Absolute Maximum Ratings:
Parameter | Symbol | Condition | Ratings | Unit | Remark | |
MIN | MAX | |||||
+3.3V supply voltage | VDD | Ta=25℃ | -0.3 | +3.6 | V | |
Backlight supply voltage | VBL | Ta=25℃ | -0.3 | +21 | V | |
Input voltage(eDP) | VI | Ta=25℃ | -0.3 | +1.5 | V | |
Input voltage(BL) | VBL_I | Ta=25℃ | -0.3 | VDD+0.3 | V | |
Storage temperature | Tstg | -10 | +60 | ℃ |
|
|
Operation temperature | Topa | 0 | +50 | ℃ |
TFT-LCD Panel Driving:
DC Electrical Characteristics | ||||||
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
+3.3V supply voltage | VDD | +3.0 | +3.3 | +3.6 | V | |
Permissible input ripple voltage | VRP | - | - | 100 | mVp-p | VDD=+3.3V |
eDP HPD Signal Characteristics | ||||||
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
HPD High level output voltage | VOHHPD | VDD-0.1 | ||||
HPD Low level output voltage | VOLHPD | |||||
eDP AUX Channel Characteristics | ||||||
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
Unit Interval for AUX channel | UIAUX | 0.4 | 0.5 | 0.6 | S | |
Peak-to-peak voltage at TP1 | VAUX-DIFF-pp | 0.32 | - | 1.36 | V | |
AUX DC Common mode Voltage | VAUX-DC-CM | 0 | - | 2.0 | V | |
AUX Short current limit | IAUX_SHORT | - | - | 90 | mA | |
AUX CH termination DC resistor | RAUX_TERM | - | 100 | - | Q | Differential input |
AUX AC coupling capacitor | CAUX | 75 | - | 200 | nF | |
Number of pre-charge pulses | Pre-charge pulses | 10 | - | 16 | - | |
eDP AUX Channel Characteristics | ||||||
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
Link clock down spreading | Down_Spread_Am plitude | 0 | 0.5 | % | ||
Differential Peak-to-peak Input Voltage at Rx package pins | VRX-DIFFp-p | 90 | 1200 | mV | ||
Differential Return Loss at 1.35GHz at Rx package pins | RLRX-DIFF | 9 | - | - | dB | |
Differential termination resistance |
RRX-TERM | - | 100 | - | Q | |
RX short circuit Current Limit | IRX-SHORT | - | 50 | mA | ||
Lane Intra-pair Skew at RX package pins | TRX-SKEW- NTRA- PAIR-High-Bit-Rate |
- |
- |
TBD | ps |
Backlight Driving:
The backlight system is an edge-lighting type with white-LED.
(It is usually required to measure under the following condition: Ta=25C±2C)
Parameter | Symbol | Min. | Typ. | Max. | Unit | Remark |
Supply voltage | VBL | 7.0 | 12.0 | 21.0 | V | |
Current dissipation |
IBL |
- |
(227) | (251) | mA | VBL=12V Duty Ratio=100% |
(135) | (135) | mA | VBL=7.9V Duty Ratio=40% | |||
Modulated light signal voltage | VPWM H | 1.85 | - | VDD | V | |
VPWM L | 0 | - | 0.7 | V | ||
Brightness Control Duty Ratio | Duty | 1 | - | 100 | % | |
Brightness Control pulse width | TPWM | 5 | - | - | ps | |
Brightness Control frequency | PWM | 200 | - | 2,000 | Hz | |
LED-BL ON/OFF High voltage | VCNT H | 1.8 | 3.3 | 3.6 | V |
Optical Specification:
Paramete | Conditions | Min. | Typ. | Max. | Unit | |
Viewing Angle(CR>10) |
Horizontal | L | - | 89 | - |
degree |
R | - | 89 | - | |||
Vertical | T | - | 89 | - | ||
B | - | 89 | - | |||
Contrast Ratio | Center | 700 | 1000 | - | - | |
Response Time | Tr+Td | - | 25 | ms | ||
CF Color Chromaticity(CIE1931) |
Red x |
Typ. -0.05 |
TBD |
Typ. +0.05 |
- | |
Red y | TBD | - | ||||
Green x | TBD | - | ||||
Green y | TBD | - | ||||
Blue x | TBD | - | ||||
Blue y | TBD | - | ||||
White x | (0.313) | - | ||||
White y | (0.329) | - | ||||
NTSC ratio | % | (72) | - | |||
Luminance of white | YLI | 220 | cd/m |
Reliability Test Items:
No. | Test Item | Conditions |
1 | High temperature storage test | Ta=60℃ 72h |
2 | Low temperature storage test | Ta=-10℃ 72h |
3 |
High temperature & high humidity operation test |
Ta=40℃90%RH 72h (No condensation) |
4 | High temperature operation test | Ta=50℃ 72h |
5 | Low temperature operation test | Ta=0℃ 72h |
[Result Evaluation Criteria] Under the display quality test condition with normal operation state. Do not change these condition as such changes may affect practical display function.
[Normal operation state] temperature :+ 15~ +35C ,Humidity :45~75% ,Atmospheric pressure :86~106kPa
Matters Needing Attention:
1.Do not use polychloroprene. If you use it, there is some possibility of generating Cl2 gas that influences the reliability of the connection between LCD panel and driver IC.2.Do not put a laminate film on LCD module, after peeling of the original one. If you put on it, it may cause discoloration or spots because of the occurrence of air gaps between the polarizer and the film.