Barrier Gate Operator Folding Arm Anti Collision Swing Out 90° / 180°
DZ-115 Barrier Gate Operator controller -- variable frequency type, is the enhanced Barrier Gate Operator control for adjusting speed. Adopting full remote control mode, with the open /stop/close wire control interface, counting interface, special encoder limit interface, loop detector interface, infrared interface, open limit, close limit output interface, and communication interface. The remote control code is the learning code, and the receiver module adopts external superheterodyne reception.
Barrier Gate Operator Functions
1. Barrier Gate Operator steady function, sensitive reaction, low noise
2. The case shell is made of thickened steel shaped by 13 process flow. Without fading, waterproofing is not rusty, or durable.
3. High-sensitive limit switch, the pole can be instantly turned on and off accurate location.
4. The control system adopts hi-tech digital chip technology.
5. the anti-collision function. Protecting the passenger
6. the inductive function, of the digital vehicle detector
7. the movements adopt the most steady running mode –non-constant speed mode. Or the variable speed excogitation. (Slow – quick – slow ) 8. This function makes the operation steady and prolongs the working life.
Barrier Gate Operator Optional Accessories:
1. Loop detector: single loop detector or dual channel loop detector |
2. Photocell |
3. Flashlight |
4. Boom rest/ arm holder |
5. Control board |
6. RS485 communication interface |
Each barrier will include:
1 pcs Barrier |
1 pcs arm boom (from 1m to 6m can customized) |
1 pcs control panel(built inside) |
2 pcs remote controllers, 1 pc push button |
1 pcs manual book |
Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator Barrier Gate Operator
Barrier Gate Operator Specifications
Model | WSTP-115 |
Working Temperature | -40℃~+75℃ |
Voltage | 220V±10%, 110V±10%, 50/60HZ |
Rated power | 80W |
Relative humidity | ≤90% |
Remote control distance | ≥30m |
Net weight | 48kgs |
Speed | 1S,1.8S,3S, 6S |
Max boom length | 6 meters |
Motor Rotational speed | 1400rmp |
Protection Degree | IP44 |
Communication with customers
1) Q: Connected power and pressed open/close button but the traffic barrier gate did not action.
A | Reason | Solution |
1 | Fuse blown | Check the fuse and power in the controller |
2 | The battery of the remote control powered off | Change a new one |
3 | External protection circuit break or at protecting status | Open the barrier door and click the OPEN/CLOSE button on the control box |
4 | Same frequency interference | Check photocell and loop detector |
2) Q: When you connect the power and press the open/close button, the traffic barrier gate will move, but even when it is in the right position, the motor is still running and will not stop.
A | Reason | Solution |
1 | Limit switch | Adjust the horizontal/vertical limit switch to the correct position |
2 | Main controller failure | Change a new one |
3) Q: The motor running but the traffic barrier gate arm is not in action?
A | Reason | Solution |
1 | Barrier arm at 45° position where is hard to move | Unlock the clutch and manually rotate the arm to a horizontal or vertical position then try again |
2 | The tension of the balancing spring is not suitable | Adjust spring exactly |
3 | Low working voltage | Check the voltage and power |
4) Q: When opening/closing, traffic barrier gate arm cannot reach the right position (90° vertical & 180° horizontal)?
A. | Reason | Solution |
1 | Length adjustment of connecting rod not correct | Open the barrier door and unlock the clutch to check when the arm is at 90° vertical position if the master rod covers slave one; when the arm is at 180° horizontal position if the master rod and slave one are in the same straight line |
2 | Nuts on the limit switch loose | Tighten the nuts when arm at 90° vertical and 180° horizontal |
1. Q: How long will your barrier work?
A: barrier life span more than 10 years.
2. Q: What should we do if there are problems during use?
A: We have 2 year guarantee. If any barrier problems you have, Welcome to email or call me! We will provide our best professional service for you.
3. Q: First-time import, how can I believe that you would send a product?
A: We are a verified company by Everychina, to make transactions successful.
4. Q: How to import your machines?
1. We will prepare the barrier and shipment for you after payment;
2. We will give you a bill of loading after the barrier departs our shipping port;
3. Our shipping agent will contact you when the barrier arrives;
4. You can pick up barriers by bill of loading.
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype: SueZhang729
Whatsapp:+86 158 7925 9831