Multistage, frequency controlled 3" submersible pump in jacketed construction for vertical or horizontal installation

For pumping rainwater and industrial water from boreholes and wells for sprinkling, irrigation and water supply.

TWU 3-...-HS-I

• Integrated non-return valve
• Integrated frequency converter with the following functions:
  • Soft starter
  • Undervoltage, overvoltage and short-circuit protection
  • Thermal overload protection of the motor and frequency converter
  • Dry-running protection

TWU 3-...-HS-ECP-B

• Integrated non-return valve
• External frequency converter with the following functions:
  • Soft starter
  • Undervoltage, overvoltage and short-circuit protection
  • Thermal overload protection of the motor and frequency converter
  • Constant pressure control
  • Leakage detection for avoiding excessive switching cycles (pulse)
  • Dry-running protection with automatic reset
  • Change of direction of rotation
  • Settings for max. current and nominal pressure
  • Pressure indicator on the display
  • Settings, operating statuses and error messages are shown by LEDs and on the display

Constant pressure control function

The frequency converter controls the speed of the pump based on the nominal pressure. As a result, the submersible pump always delivers a constant pressure.

Submersible pump:

• Supply voltage: HS-E…: 1~230 V, 50/60 Hz (connection via the frequency converter to the AC mains supply) HS-I...: 1~230 V, 50/60 Hz (direct connection to the AC mains supply)
• Submerged operating mode: S1
• Fluid temperature: 3 – 35 °C
• Minimum flow rate at motor: 0.08 m/s
• Max. sand content: 50 g/m3
• Max. number of starts: 30/h
• Max. immersion depth: 150 m
• Protection class: IP58
• Discharge port: Rp 1/Rp 1¼

Frequency converter for version “HS-E…”:

• Mains connection: 1~230 V, 50/60 Hz
• Output: 3~230 V/max. 140 Hz/max. 2.2 kW
• Fluid temperature: 3 – 50 °C
• Max. pressure: 8 bar
• Protection class: IPX5
• Connection: G 1¼

• Hydraulics housing: 1.4301
• Impellers: Polycarbonate
• Hydraulic shaft: 1.4104
• Motor housing: 1.4301
• Motor shaft: 1.4305

Submersible pump for vertical or horizontal installation.

Hydraulics

Multistage submersible pump with radial impellers in sectional construction and integrated non-return valve. Discharge port with threaded flange and female thread. All parts that come in contact with the fluid are made of corrosion-free materials.

Motor (...HS-E...-B)

Corrosion-free permanent magnet motor for connection to the supplied frequency converter. Oil-filled motor with self-lubricating bearings, designed for high speeds up to 8400 rpm.

The frequency converter is installed directly in the discharge pipeline outside the fluid (flood-proof). The motor is cooled by the pumped fluid.

Motor (...HS-I)

Corrosion-free asynchronous motor with integrated frequency converter for direct connection to the mains supply. Rewindable, oil-filled motor with self-lubricating bearings, designed for high speeds from 8400 rpm.

Cooling

• The motor is cooled by the pumped fluid. Always operate the pump in a submerged state.
• Vertical installation is possible with or without cooling jacket.
• Horizontal installation must be performed in conjunction with a cooling jacket.

• Hydraulics + motor completely assembled
• Frequency converter (...HS-ECP)
• 1.75 m connection cable
• Installation and operating instructions

• Cooling shroud
• Diaphragm expansion tank
• Gate valve
• Float switch
• Pressure switch
• Electrode
• Switchgear
• Alarm switchgear
• Casting resin kit
• Connection cable